Printed in U.S.A. All product names are trademarks of their respective companies. Table of Contents Title Page Introduction..................................................................................................................... 1 How to Contact Fluke ..................................................................................................... 2 Connecting to a HART Transmitter ................................................................................ 3 Supported vs. Ge

Diese Nennspannungen können mit dem Spannungswähler (kombiniert mit der Netzbuchse an der Geräterückwand) eingestellt werden. Die Sicherung befindet sich in einem Halter am selben Platz. Zum Einstellen der Netzspannung oder zum Ersetzen der Sicherung ist das Netzkabel herauszuziehen und die Verschlußklappe mit einem Schraubenzieher zu öffnen (siehe Zeichnung). PM 5414 V INSTALLATIONS- UND SICHERHEITSANWEISUNGEN 1 - 3 Die geeignete Spannung ist durch Drehen des Stellrades zu wählen. Falls erfo

Wenn der Inhalt unvollständig ist oder wenn Defekte wahrgenommen werden, muß beim Überbringer sofort reklamiert werden. Eine Fluke Verkaufs- und Servicestelle muß ebenfalls verständigt werden, um Reparatur oder Ersatz des Gerätes zu ermöglichen. (D PM 5415 / PM 5418 INSTALLATIQNS- UND SICHERHEITSANWEISUNGEN_;_1 - 1 1 INSTALLATIONS- UND SICHERHEITSANWEISUNGEN 1.1 SICHERHEITSANWEISUNGEN Das Gerät hat das Werk in sicherheitstechnisch einwandfreiem Zustand verlassen (siehe Kapitel 4). Zur Erhal

All rights reserved. All product names are trademarks of their respective companies. User’s Guide – version 3.5 NetFlow Tracker Contents SOFTWARE LICENSE AGREEMENT 5 INTRODUCTION 15 What is NetFlow? 15 What is NetFlow Tracker? 15 Features and Benefits 15 INSTALLATION 17 Minimum System Requirements 17 Operating System Support 17 Pre-installation Checks 17 Installation on Microsoft Windows 18 Installation on Linux 19 Post-installation Tasks 19 USING NETFLOW TRACKER 21 Real-time Data 21 Long-term D

Amp. 70 % 100 % 30 % 24 % 48 % 100 % 120 % 112 % 80 % Lead I reference Performance waves and R wave detection Lead # I II III V1 V2 V3 V4 V5 V6 Ref. Amp. 100 % 150 % 50 % 100 % 100 % 100 % 100 % 100 % 100 % Normal Sinus waves Lead # I II III V1 V2 V3 V4 V5 V6 Ref. Amp. 100 % 150 % 50 % 24 % 48 % 100 % 120 % 112 % 80 % ECG Normal Sinus Rates................................................................... 10 to 360 (by 1) BPM ECG High Level Output (BNC Jack) Amplitude Range ....................

& Date: 1, 2/2008 CD PN: 3028681 © 2008-2009 Fluke Corporation. All rights reserved. Printed in the U.S.A. Impulse 6000D/7000DP Users Manual Supplement Change #1, 46470, 46697, 47714, 48007, 49680 Replace pages 31 through 35, with the following: Defibrillator Analyzer Specifications Energy Output Measurement Compatible Defibrillator Waveshapes ................ Lown, Edmark, Trapezoidal, DC Bi-phasic, and AC Pulsed Bi-phasic Note AC Pulsed Biphasic waveform has not been approved in the United Sta

Materials for Cleaning the High Range Piston Cylinder 1. Prepare a clean work area near a running tap water source. 2. Prepare several sets of folded wipers as shown in Figures 6-2 through 6-4. Two wipers can be folded together for wiping the outside of the piston and cylinder. Prepare several twisted wipers as shown in Figures 6-10 through 6-12 to wipe the bore of the cylinder. 3. Disassemble the piston/cylinder assembly. 4. Insert the retaining clip from the bottom of the piston into the insta

This manual is distributed as an electronic manual on the following CD-ROM: CD Title: 1652C/1653B/1654B CD Rev. & Date: 9/2010 CD PN: 3798444 © 2010 Fluke Corporation. All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating th

• Be sure the test leads and switch are in the correct position for the desired measurement. • Never measure resistance in a circuit when power is applied. • Never touch the probes to a voltage source when the test leads are plugged into the 10 A or 300 mA input jack. • Never apply more than the rated voltage between any input jack and earth ground. • Be careful when working with voltages above 60 V dc or 30 V ac rms. Such voltages pose a shock hazard. • Keep your fingers behind the finger guard

All rights reserved. Printed in The Netherlands. All product names are trademarks of their respective companies Using the Interface Cable PC Requirements - USB 1.1 (or higher) port on the PC. - Windows XP/ 2000/ Me/ 98 Second Edition. Installing the USB- IR cable drivers - Log into an account with Administrator privileges (Windows XP or Windows 2000). - Plug the USB cable into an USB port. - Windows will respond that it has "found new hardware", and the Windows Hardware Wizard dialog will appear