Using the charger on any other voltage may overheat and damage the charger. 13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger. 14. ALWAYS disconnect the power cord from its receptacle when the charger is not in use. DISPOSAL OF THE EXHAUSTED BATTERY WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of it’s use

16008 North 81st Street Scottsdale, AZ 85260 Phone: 480-483-1214 Fax: 480-483-5620 May 2000 Notice This publication and its contents are proprietary to Universal Laser Systems, Inc. (ULS), and are intended solely for the contractual use of ULS, Inc. customers. While reasonable efforts have been made to assure the accuracy of this manual, ULS shall not be liable for errors contained herein or for incidental or consequential damage in connection with the furnishing, performance, or use of this mat

The User’s Guide contains instructions and illustrations for connections to all compatible computers. It also describes the remote control buttons and menu functions. R You must install the projection bulbs 1 the first time you use the LitePro. Refer to the “Read Me First” card or page 40 of the User’s Guide for instructions. 2 Place the LitePro on a flat surface within six feet of your power source and your computer. 3 Remove the lens cover. 4 Plug in the LitePro’s power cord. 5 Make sure your

Please keep this manual available for others before they use the power tool. MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT Une utilisation incorrecte et dangereuse de cet outil motorise peut entrainer la mort ou de serieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations a propos de la securite de ce produit. Priere de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil motorise. Garder ce mode d’emploi a la disponibilite des autres utilisateurs

Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the battery charger. This manual should be stored in safe place. INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI AVERTISSEMENT Une utilisation INCORRECTE OU DANGEREUSE de ce chargeur de batterie peut entrainer la mort ou de serieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations a propos de la securite de ce produit. Priere d

(Premium - If you have a HDMI port on your HDTV receiver and a M1 port on your projector, see page 5. For more information and troubleshooting... Read the tips, common issues and frequently asked questions on pages 6-8. InFocus' CORPORATION Connect an HDTV receiver to a component-ready projector using a component video cable Setup Requirements • HDTV receiver with component video-out ports • Projector with component video-in ports • Component video cable (red, green, blue male RCA) €>

Please keep this manual available for others before they use the compressor. — CONTENTS — Page IMPORTANT INFORMATION ...............................2 MEANINGS OF SIGNAL WORDS ........................2 SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE COMPRESSOR........3 REPLACEMENT PARTS ........................................5 GROUNDING INSTRUCTIONS ............................5 EXTENSION CORD ...............................................6 Page OPERATION AND MAINTENANCE NAME OF PARTS......

22. Have your tool repaired by a qualified person. This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts. Otherwise this may result in considerable danger to the user. PRECAUTIONS ON USING ROTARY HAMMER 1. Wear earplugs to protect your ears during operation. 2. Do not touch the bit during or immediately after operation. The bit becomes very hot during operation and could cause serious burns. 3

E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum) commercially available. Use the mounting points on the center of the plate as indicated in the assembly diagram. ° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially available hardware (depending on the installation requirements). Use the mounting points found on the outer points of the mounting plate as indicated in the assembly diagram. F. Allen wre

.............. Rotary Hammer .......... HANDLING INSTRUCTIONS DH 22PB 1 1 2 4 6 8 3 5 7 1 2 3 4 4 5 6 9 10 13 16 14 15 CDB HJ KLM ONKP1211 EFG1HI3417 18 L349 10 13 16 14 15 CDB HJ KLM ONKP1211 EFG1HI3417 18 L34 3 1 .... 2 .................. ...... 3 .... 4 .... 5 ...... 6 ............ 7 .... 8 ...... 9 .... 0 ........ A .......... B ............ ...... C ........ D ...... E .... F ...... G ...... H .......... I .... J .... K ........ L ........ M .... N ...... O .... P ............ Drill bit Par