Login:
heruntergeladen wurde: 14   Dateigröße: 643 kb   Hersteller: Bradley Smoker  
Kategorie: Plumbing
@name@name@name

2 Wall Shower Components .................... 2 Wall Shower Dimensions ..................... 3 Step 1: Rough-In Piping ...................... 3 Step 2: Install Shower ........................ 3 Vertical Shroud Installation ................... 4 Horizontal Shroud Installation ................4 Table des Matieres Fournitures requises ......................... 5 Hauteurs de douche conseillees .............. 5 Elements de la douche ......................5 Dimensions de la douche ....................

heruntergeladen wurde: 44   Dateigröße: 1 mb   Hersteller: Honda Automobiles  
Kategorie: Plumbing
@name

The information and specifications included in this publication were in effect at thetimeofapprovalforprinting.HondaMotor Co., Ltd. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No partofthispublicationmay be reproduced without written permission. INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safetyof others are very important. And using this water pump safely isan important res

heruntergeladen wurde: 24   Dateigröße: 2 mb   Hersteller: Honda Automobiles  
Kategorie: Plumbing
@name

It must be available to all operators of the pump and should remain with the pump if resold. The information and specifications in this publication are based on the latest product information available at the time of printing. American Honda Motor Co., Inc. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. It is illegal in some areas to operate an engine without a U.S.D.A.

heruntergeladen wurde: 0   Dateigröße: 463 kb   Hersteller: Delta  
Kategorie: Plumbing
@name

Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 2 REAR OF SINK 4 5 6 3 1 SINK DRAIN HOLE FLAT SIDE OF GASKET MUST FACE DOWN 1 2 Fig. A. 2 1 FLAT SIDE OF GRAY LOCKNUT MUST FACE UP INSTALL GRAY LOCKNUT 5 Install GRAY LOCKNUT (1) onto DRAIN BODY (2) fro

heruntergeladen wurde: 1   Dateigröße: 463 kb   Hersteller: Axor  
Kategorie: Plumbing
@name

*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Speed Connect™ Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Turn off water at CAUTION main supply. INSTALL

heruntergeladen wurde: 13   Dateigröße: 463 kb   Hersteller: American Standard  
Kategorie: Plumbing
@name

Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3), HANDLE COLLAR (4) and O-RING (5). 3 2 6 1 4 7 Thread HANDLE ASSEMBLY (6) into ball of HANDLE BASE (7). Apply pressure to the MOUNTING ROD ASSEMBLY (1) while turning the HANDLE COLLAR (4), in order to tighten firmly. 5 SERVICE ALIGN HANDLES 11 To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Pull out INDEX CAP and remove HANDLE SCREW. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace S

heruntergeladen wurde: 0   Dateigröße: 463 kb   Hersteller: Hans Grohe  
Kategorie: Plumbing
@name

Insert FAUCET (1) and CABLE CONNECTOR (2) through mounting holes of Sink or mounting surface. Fig. A. Assemble LOCKNUTS (3) onto SHANKS (4) ( from under side of Sink. Hand tighten firmly. Fig. B. 2 2 1 4 3 3 4 (HAND TIGHTEN) M968422Rev.1.2 TM Fig. A. Fig. B. 1 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Delta  
Kategorie: Plumbing
@name

Place it in the sink outlet. From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly. Tighten the retainer nut. Place the plunger assembly in the drain. Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster. Install and ha

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Hans Grohe  
Kategorie: Plumbing
@name

incoming hot water temp. 176°F* Recommended incoming hot water temp. 120° - 140°F* Max. flow rate -- lavatory faucets 2.2 gpm Max. flow rate -- bidet faucet 2.2 gpm The bidet faucet is not suitable for use on vertical spray bidets. This faucet may be used with a continuous flow water heater if the flow pressure is at least 20 PSI. For best results, Hansgrohe recommends that this faucet be installed by a licensed, professional plumber. *Please know and follow all applicable local codes when setti

heruntergeladen wurde: 0   Dateigröße: 1 mb   Hersteller: Axor  
Kategorie: Plumbing

mounting surface thickness 1 1/8" Hole sizes in mounting surface Spout 1 3/8" Valves 1 1/4" Max. incoming water pressure 145 PSI Recommended incoming water pressure 22 - 72 PSI Max. incoming hot water temp. 176°F* Recommended incoming hot water temp. 120° - 140°F* Max. flow rate -- lavatory faucets 2.2 gpm Max. flow rate -- bidet faucet 2.2 gpm The bidet faucet is not suitable for use on vertical spray bidets. This faucet may be used with a continuous flow water heater if the flow pressure is at





Kategorien