3. Reinstalling auto.darkening lens assembly . Gently place auto. darkening lens in front of helmet. (Be careful not to drop lens.) Install front lens cover with gasket. Grasp front lens holder and slowly insert the six retaining pieces into front of helmet. (Make certain you gently squeeze the outside edges of the front lens holder while inserting tabs into helmet.) From the inside of helmet, gently push the retaining tabs in to secure the front lens holder in place. Page 7 SECTION 4 . BATTERY

#13 Use the shade chart below to select proper shade control setting based on your welding process. We recommend starting at shades 12 or 13 and adjust lighter based on the welding application and personal preference. Application Welding Arc Current in Amperes Protective Shade No. Stick Electrodes Less than 40 40.80 80.175 175.300 #9 #10 #11 #12 . #13 MIG Less than 100 100.175 175.300 #10 #11 #12 . #13 Gas Tungsten Arc Welding (TIG) Less than 50 50.100 100.200 200.300 #10 #11 #12 #13 Page 5 Sens

READ BEFORE USING . . . . . . . . . . . . . . . . . . . . SECTION 2 . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . SECTION 3 . OPERATING INSTRUCTIONS . . . . . . . . . . . . . . SECTION 4 . BATTERY REPLACEMENT . . . . . . . . . . . . . . . . SECTION 5 . MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION 6 . TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . SECTION 7 . LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . SECTION 8 . REPLACEMENT

specifications HP NetServer LH 4 and LH 4r Features Performance Processor Up to 4 Intel Pentium III Xeon 550MHz processors with 100MHz system bus Level 2 Cache 512KB1, 1MB2, 2MB3 ECC Memory · 256MB high-performance 50ns ECC buffered EDO DRAM standard • Memory scrubbing reduces accumulated ECC errors that cause system crashes • 4GB maximum capacity I/O Expansion Slots 8 total full-length PCI (two 64-bit, one occupied by preinstalled 10/100TX NIC, 1 shared with 2/3 length ISA) Controllers · Integr

Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard Co. shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or the examples herein. Consumer transactions in Australia and the United Kingdom: The above disclaimers and limitations shall not apply to

. The welder control panel contains information regarding proper input 3 Operating Instructions GTAW Arc Welding Torch voltage and amperage. Follow the specifications on the welder front panel. . The receptacle used for the welder must be properly grounded and the welder must be the only load on the power supply circuit. The Components of TIG Welding (not included with your WT6100 TIG torch) are: 1. A constant current power supply such as the Arcitech 110 inverter technology arc welder. 2. A bot

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or Notes property damage! Retain instructions for future reference. Notas BUILT TO LAST Aluminum Welding Kit Description Model WT2531 is an aluminum welding kit designed for use on Campbell Hausfeld wire feed MIG welders (WG206X and WG208X series). This kit includes: Teflon ® wire liner (Part Number: WC403621AV) , smooth-groove drive roller (Part Number: WC5008

When the speed is to slow, the weld metal piles up and the bead is high and wide. SlAG ReMOVAl Wear ANSI approved safety glasses (ANSI Standard Z87.1) and protective clothing when removing slag. Hot, flying debris can cause personal injury to anyone in the area. After completing the weld, wait for the welded sections to cool. A protective coating called slag now covers the weld bead which prevents contaminants in the air from reacting with the molten metal. Once the weld cools to the point that

Electrodes used for shielded metal arc welding have two parts. The inner core is a metal rod or wire that should be similar in composition to the base metal. The outer coating is called flux. Various types of flux exist. Each coating is used for a particular welding situation. While the metal is molten, it can be contaminated by elements in the air. This contamination could weaken the weld. The flux coating creates a protective barrier called slag that protects the molten metal from contaminants

High humidity causes moisture condensation on electrical components. Moisture can contribute to corrosion and short electrical components. Dust and dirt in the welder retain moisture and increase wear of moving parts. Place the welder in an area that provides at least twelve inches (305 mm.) of ventilation space at both the front and rear of the unit. Keep all obstructions away from this ventilation space. Store electrodes in a clean, dry location with low humidity, such as WT2240 Electrode Co