17 .... 26 WP3861 Philips Pure Taste 6 introduction English 6 introduction English Congratulations on your purchase and welcome to Philips! To fully benefit from the suppor t that Philips offers, register your product at You have made an excellent choice.The Philips Pure Taste is a compact and easy-to-install water purifier that improves the taste of your drinking and cooking water by removing chlorine and other impurities with a silver- coated activated carbon filter. Better-tasting water made

As in all plumbing products and water storage vessels, bacteria can grow in this Product, especially during times of non-use. Consult your local plumbing professional regarding any steps you may wish to take to safely disinfect your home’s plumbing system. DANGER! EXPLOSION HAZARD, WHEN THE WELL-X1™ HAS BEEN IN SERVICE AND A CHANGE TO A HIGHER PRE-CHARGE PRESSURE IS NECESSARY DUE TO A REQUIRED CHANGE IN THE PRESSURE SWITCH SETTING, FAILURE TO FOLLOW INSTRUCTION MANUAL CAN CAUSE A RUPTURE OR EXPL

This allows you to use the Well- X-Trol® “principle of separation of air and water” on larger jobs that are beyond the typical residential range. The Well-X-Trol® models we’ll be working with in this handbook are listed in Table 1. The design features of these larger models allow us to apply them more creatively than the smaller residential models found in the Well-X-Trol® 100, 200, and 250 series. The Larger Well-X-Trol®s are Designed and Built for Maximum Acceptance on Each Operating Cycle In

We now must select a pressure range (min. to max.) to establish pressurized delivery of water to the system and that we overcome elevation (static height) and friction loss of the piping. We must select a minimum pressure at the Well- X-Trol® location that will insure enough pressure to keep water flow under pressure at the top of the system…overcoming both the static height and the resistance to flow through the piping. We’ll do this by pre-charging the Well-X-Trol® to a pressure (P1) equal to

6. Slowly open the service valve to allow the system to pressurize. The pressure may drop slightly during this process. After the valve is fully open, open the fixture closest to the Well-X1™ to begin drawing water from the tank. 7. When the system reaches the factory cut-in (pump on) setting of 40 psig, the pump will start. Like a traditional mechanical switch, the pressure will begin to rise, repeating the cycle. If desired, the Well-X1™ settings can now be adjusted as shown below. OPEN CLOSES

Hilex, Clerox, etc.) and mix in the water. DO NOT ADD CHLORINE FIRST. Concentrated, it will attack plastics, 6. Replace the cap, with o-ring, and install the retaining clamps. 7. Connect the RO faucet product water tubing directly to the tank shutoff valve, isolatinq the carbon postfilter. 8. Open the tank shutoff valve, and the water supply to the RO. Open the RO faucet, locking the lever upward, against the spout. 9. Allow water to circulate through the system until the bleach odor is gone. 10

It has a hand operated, spring loaded lever to keep the faucet closed and to prevent waste. You can keep the faucet open by pushing upward on the lever and locking it against the spout. To meet plumbing codes, an air-gap is built into the faucet drain water tubes. The air-gap prevents a back siphon of drain water. MONITOR -When the faucet is opened, lights on the faucet base show how the RO system is working. • FLASHING GREEN -The RO system is giving you high quality product water. NOTE: The gre

Locate clamp A (turn handle in to align pin if pre- drilled hole) and clamp B on the pipe. Fasten in place using 2 screws. Tighten each screw evenly, STEP 2 --INSTALL THE • Before beginning, be sure to read the note on page 5. • The drain adapter fits 1-1/2" sink drain pipe. • The adapter installs directly onto the s(nk tailpiece as typically shown in fig. A and B. • Locate so drain tubing from the faucet (FIG. 7, page 10) makes a straight run to the adapter, without dips, loops, low spots or ki

See 1-800-86 WATER performance data sheet for details, Manufactured by EcoWater Systems, Inc, PO BOX 64420, ST. PAUL, MN 55164 Part No. 721 4105 (10/99) -TABLE OF CONTENTS Safety Guides ................................................ 2-3 What Your Home Drinking Water System Will Do ..................... 3 Things To Check Before You Start To Install ....................... 4-5 How To Install Your Home Drinking Water System ................. 5-11 How Your Home Drinking Water System Works ........

Trinkwasserqualitat ist nur bei fristgerechter Uberwachung der Anlage gewahrleistet. Beachten Sie die angegebenen Kontrollintervalle. . Lassen Sie die Trinkwasserqualitat in regelma.igen Abstanden uberprufen, die gultige Trinkwasserverordnung ist zu beachten. Chemikalien . Benutzen Sie saurefeste Schutzkleidung (Brille und Handschuhe). . Lagern Sie die Chemikalien kuhl und trocken, jedoch nicht unter 5 °C. . Bewahren Sie die Chemikalien an einem fur Kinder unzuganglichen Ort auf. . Sorgen Sie fu