Cable ID locators (optional) to identify link connections at a patch panel (twisted pair only) Note Running network tests on a fiber link requires an optional SFP module. Accessing the Product Manuals This guide provides basic information to help you get started using the module. For more detailed information, see the latest versions of the DTX Series Users Manual and the DTX Series Technical Reference Handbook provided on the DTX Product Manuals CD and on the Fluke Networks website. PN 2544310

The second alternative is to use ArbExplorer for high-level programming. ArbExplorer is a software package supplied with the Instrument that simulates a set of mechanical front panels. It has all the necessary push buttons, displays and dials to operate the Instrument as if you were using it on the bench. The third alternative is using application specific drivers, such LabVIEW or IVI. The Instrument must be programmed to generate waveforms. Therefore, it is recommended that the user becomes fam

°C and °F To toggle between °C (Celsius) and °F (Fahrenheit) measurements, press the Menu softkey until °C or °F appears as the left softkey function. Press the corresponding softkey to change between the measurements. Min, Max, Avg, Differential The thermometers can measure minimum (MIN), maximum (MAX), average (AVG), or differential (.) temperatures each time a reading is taken. These values are not shown if a thermocouple is plugged into the thermometer. To turn on the Min Max mode: 1. Press

Printed in USA All product names are trademarks of their respective companies. Limited Warranty & Limitation of Liability This Fluke product will be free from defects in material and workmanship for 3 years from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse or abnormal conditions of opera tion or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain service during the warranty per

Printed in USA. All product names are trademarks of their respective companies. LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obt

Chapter 2 of the Users Manual of the ScopeMeter explains how to display the software version. This Chapter also explains how to exchange the Battery Pack. After installation, charge the Battery Pack for at least 7 Hrs. with the ScopeMeter switched off. • Nominal Voltage: 4.8 V • Capacity: 3.0 Ah • Lifetime: minimum 500 cycles at nominal charge of 500 mA • Temperature Ranges: Operating: 0 ° C to 50° C Quick Charging: 10° C to 40° C Trickle Charging: 10° C to 45° C Storage: -40° C to 60° C Perform

Mit der Freigabetaste (REVEAL) der Fernbedienung können zusätzlich die verdeckten Zeiten und Daten sichtbar gemacht werden. In Ihrer Bedienungsanleitung des Videorekorders finden Sie Hinweise, wie durch Verwendung von VPT programmiert wird. 6-6 VIDEOTEXT (TOP/FLOF), DIDON ANTIOPE PM 5415 / PM 5418 Die Videotext-Seiten haben folgenden Inhalt (Software Version 3.2): Seite Inhalt Bemerkungen/Anwendung 100 101 102 111 150 200 201 202 203 204 205 300 310 400 401 402 403 555 560

This manual is distributed as an electronic manual on the following CD-ROM: CD Title: 1652C/1653B/1654B CD Rev. & Date: 9/2010 CD PN: 3798444 © 2010 Fluke Corporation. All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating th

Short (or apply 0 mV) to the copper wires at the Calibrator. 5. Verify the thermometer reads 0.0 oC ± 0.3 oC. 6. If this test fails, reposition the thermocouple wires and Mercury thermometer to the same depth in the ice bath, and repeat steps 3-5. If the test continues to fail, perform the calibration procedure, located after this procedure. 7. Remove the short applied in step 4. 8. Using Table 3, steps 2-5, obtain an output from the Calibrator equal to the values in the “Input Voltage (mV DC)”

592101 Fluke Corporation, Hart Scientific Division (Hart) warrants this product to be free from defects in material and workmanship under normal use and service for a period as stated in our current product catalog from the date of shipment. This warranty extends only to the original purchaser and shall not apply to any product which, in Hart’s sole opinion, has been subject to misuse, alteration, abuse or abnormal conditions of operation or handling. Fluke Corporation, Hart Scientific Division