Such damage is not covered by the warranty] Water is not hot: Check if electrical supply to heating tank is plugged in. Turn temperature control knob clockwise as far as possible. Test the temperature again after 15 minutes. Check if fuse is blown or circuit breaker is open. Hot water continuously drips or sputters from spout: For safety reasons this faucet may drip or splutter after use. This venting prevents a build-up of pressure in the heating tank. If this becomes excessive; Turn the

W9223028 For use in Filter Model No. FRCNSTR/ FRC05 The system is tested for the following performance claims as verified and substantiated by test data: • Chlorine Reduction (Taste & Odour) • Particulate reduction; • Turbidity reduction; • Cyst reduction (including Giardia and live Crypto-sporidium); Systems tested for Cyst Reduction may be used on disinfected water that may contain filterable Cysts. Do not use where water is microbiologically unsafe or of unknown quality without adequ

The dispensing head comes with three 1/4” copper tubes and one silicone tube. The two shorter (12”) copper lubes are connected to the incoming water supply via the canister. The supply to the cold side may be diverted through a chiller before the dispensing head, if required. The longer (18”) copper tube is connected to the inlet of the tank. The silicone tube is connected to the outlet of the tank using the hose connector. Preparing for the Installation As with any sink related device, it is

co m Franke Little Butler Installation, Care and Maintenance Overview of Installation There are three main components to the system, the dispensing head, the canister and the heating tank. The dispensing head comes with three 1/4” copper tubes and one silicone tube. The two shorter (12”) copper lubes are connected to the incoming water supply via the canister. The supply to the cold side may be diverted through a chiller before the dispensing head, if required. The longer (18”) copper tube is

These include pre-filter and carbon cartridges. Filter cartridges are easily replaced by removing the stainless steel cartridge housing’s cap. This automatically shuts off the water supply and allows the new cartridge to be inserted quickly and cleanly. It is recommended that a new cartridge is used every 6-12 months according to water quality. Any noticeable reduction in the filtered water’s flow rate usually indicates a new cartridge is required. Franke Uniftow and Little Butler™ Systems wor

Davlumbaz Uzivatelska Poirueka Odsavac par FDB 9078 SIL-K INDEX EN RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS ............................................................................................................................................................. 4 INSTALLATION.............................................................................................

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-1600 Series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Inlet connections: 1/2. NPSM Please read our instruction before you

Remove all contents from the package and check for completeness (see itemized table and picture). NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Spray head 3 Counter weight and gaskets 4 Fastening set (rubber washer, triangular flange, metal washer, threaded nut) 5 Hexagonal wrench 6 Valve-holder 2/8 2. Remove all mounting hardware from protective plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into th

NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENTS 1 Faucet 2 Wall fastening set 3 Wall flange (over the sink) 4 Wall flange (under the sink) 5 Fastening set (rubber washer, triangular flange, metal washer, nut) 6 Non-return valves 1 5 6 3 4 2 2. Remove all mounting hardware from protecting plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into the desired location. NOTE: the rubber O-ring should be sitting on top of

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-3000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Tailpipe connections: 3/8. O.D. Please read our instruction before