Always hold the plug, and never pull the cord. 12. Extreme caution must be used when moving a drip pan containing hot oil or other hot liquids. 13. Do not cover crumb tray or any part of the oven with metal foil. This may cause the oven to overheat. 14. Use extreme caution when removing the tray, racks or disposing of hot grease or other hot liquids. 15. Alwaysunplug the appliance before cleaning. 16. Do not clean the inside of the oven with metal scouring pads. Pieces can break off the pad and

Models := EURO-PRO x 1104HV r 1104HW 1 Year Limited Warranty This warranty applies to defects resulting from imperfections in manufacture of parts entering into the manufacture and assembly of the sewing machine which this warranty accompanies, for a period of one (1) year, subject to the following conditions, exclusions and exceptions. This warranty is enforceable if said sewing machine is given reasonably good care and proper maintenance in accordance with the accompanying printed instr

5. After re-assembling your oven, we recommend that you run it at the highest temperature ( 450° F) on the Toast Function for approximately 15minutes to eliminate any packing residue that may remain after shipping. This will also remove all traces of odor initially present. Please Note: Initial start-up operation may result in minimal smell and smoke (about 15 minutes). This is normal and harmless. It is due to burning of the protective substance applied to the heating elements in the factory. 3

Read all instructions before using your Garment Steamer. 2. Use the system only for its intended use. 3. To protect against a risk of electric shock, do not immerse any part of the system in water or other liquids. 4. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect. 5. Do not allow cord to touch hot surfaces. Let the system cool completely before putting away or opening water tank (removing the safety cap) . Wrap cord loosely around system when storing. 6. A

Please note that youcan also achieve continuous steam in the vertical position. Ironing With Steam •Make sure that the Steam Station is unplugged from the power source. •Set the variable steam control (2) TO “0”. (Fig. 3) •Fill the water tank (8A) with tap water, following the instructions for filling the water tank. •Make sure that the iron is resting on top of the rubber mat (10). IMPORTANT: Do not place the rubber mat (10) on a table or any other surface which may be damaged by heat. •Plug t

Note: We recommend that you drain the water tank after every use. Caution: Upon initial use, the steam wil be mixed with water, hot enough to scald. Ensure that the floor brush is resting on the floor or the hose handgrip is directed away from user when steam switch is turned on. Never direct the nozzle or brush end of the unit toward yourself or anyone near you. OPERATING INSTRUCTIONS cont. 7 4. Fold the other side of the towel as shown in Fig. C. 3. Fold the towel as shown in Fig. B 6. Place t

Rethread the machine. - The needle is threaded incorrectly. Make sure that the needle is threaded from left to right. - The needle is not properly inserted. - The batteries are installed backwards. Check the placement diagram in the battery compartment and reinstall. Caution: When removing fabric after sewing, first turn the hand wheel to raise the needle to the highest position. Then lift the presser foot and remove the fabric. This will prevent the needle from bending. 3. The sewing mac

The electrical equipment (motor, foot control, light, etc.) are warranted free from defects in material and workmanship for a period of two years from the date of original purchase. Non-durable parts including, without limitation, needles, belts, bobbins, bulbs, bobbin cases, shuttles, springs, and parts which normally require replacement are specifically excluded from this warranty. This warranty is void if: (a) This product has been cleaned, serviced, modified or tampered with by anyone other

Read all instructions before using your Ninja Master Prep. 2. Close supervision is necessary when any appliance is used by or near children. 3. To protect against electric shock, DO NOT immerse cord, plug or any part of the main unit in water or any other liquids. 4. DO NOT let cord hang over edge of table or counter, or touch hot surfaces. 5. DO NOT operate appliance with damaged cord or plug or after the appliance malfunctions, or is dropped or has been damaged in any manner. Return appliance

S.S. ) DECORATIVE EDGING Turn the ra w edgeunder 2cm a nd press. P lace the fabric rightsideup with the middle of the turnover under the center of the presser foot, so thatthe stitch s ews on to the fold a nd just aver the ta,w ed^e underneath. iW^IvWM SEWING BUTTONHOLES The built -in buttonhole mechanism of this machine makes it possible to sew button holes in a short time without turning the material. .................................................. Model 377/374 Model 373/372/372H P