For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Factory Recommends Professional Installation ALL UNITS TESTED AND Manufactured by National Steelcrafters of Oregon Inc. _ ^ ^ __ . __ ÔfMTfONAL STEELCRAFTERS OF $ P.O. Box 24910 oneûûNiNc icBOTL-116 NER-QA-219 Eugene, Oregon 97402 3S7 1000 PAGE 1 Thank you for purchasing the Breckwell Pellet Burning Stove. You are now pr

The fireplace and chimney should be cleaned thoroughly before starting the installation. We suggest painting the interior of particularly old and dirty fireplaces to seal any odors. In zero-clearance fireplace installations, when the fireplace opening is above the floor or raised hearth, the adjustable “Breckwell P24 Z-C Skirt” (part # A-ZC-SKRT), or “Breckwell P24 Z-C Legs” (part #A-S-ZCLEGS), can be used to bridge the gap between the hearth and stove bottom. (Refer to figure 13) A. ASSEMBLING

Contact may cause skin burns. Educate all children of the danger of a high temperature stove. Young children should be supervised when they are in the same room as the stove. If the stove is installed in a room without air conditioning, or in an area where direct sunlight can shine on the unit, it is possible this can cause the temperature of the stove to rise to operational levels; one of the sensors could then make the stove start on its own. It is recommended that the stove be unplugged when

If connected to an older, two-prong outlet, a separate ground wire should be run to a proper ground (refer this to a qualified technician). Always route the electrical cord so that it will not come in contact with any hot part of the stove. FIGURE 18 SPECIAL MOBILE HOME REQUIREMENTS WARNING: DO NOT INSTALL IN A SLEEPING ROOM. For installation in a mobile home, an outside source of combustion air must be used (See “COMBUSTION AIR SUPPLY”). The P2000 must be grounded to the steel chassis of the ho

It is important to remove this creosote since it is highly combustible. INSPECT BEHIND THESE COVER PLATES AT LEAST ONCE PER HALF TON OF PELLETS BURNED UNTIL YOU ARE FAMILIAR WITH HOW ASHES AND CREOSOTE ACCUMULATE WITH YOUR OPERATING PRACTICES. NOTE: Cover plate screws need to be snug only. Hand tight Is normally sufficient. a Cleaning — Over a period of time, ashes or dust may collect on the blades of both the combustion blower and convection blower. Periodically the blowers should be vacuumed

ASH DISPOSAL - INSERT Remove ashes periodically as they fill the firebox. To remove ashes: a. Make sure fire is out and firebox is cool. b. With the door closed clean heat exchanger tubes. c. (See “CLEANING” and Figure 24). d. Open door and remove the optional imitation log set, if in use. Remove the burnpots inner section by grasping it and pulling straight up (see Figure 25). e. Empty ashes from the inner section and scrape with cleaning tool; make sure holes are not plugged. f. Use small shov

For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. • PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury, or even death. • Save these instructions PROFESSIONAL INSTALLATION IS HIGHLY RECOMMENDED Manufactured by National Steelcrafters of Oregon, Inc. D

P.O. Box 2501 Eugene, Oregon 97402 MODEL P24I MODEL P24FS Fireplace Insert Freestanding Stove 6-90 SAFETY NOTICE: If your appliance is not properly installed a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. ALL UNITS TESTED AND LISTED BY I.C.B.O. TL128 accredited ©NATIONAL STEELCRAFTERS OF OREGON. INC. Thank you for purchasing the Breckweil Pelle

Pedestal: 40 lbs. Legs: 13 lbs. Flue size: 3” or 4” Hopper Capacity: Up to 60 lbs. (this can vary widely depending on pellet size, length, and diameter) EPA status: exempt Burn time: 1 lb. to 5 lbs. per hour BTU range: 8,200 to 47,000 Approved installations: mobile home, alcove, conventional FIREPLACE INSERT: Width: 21” (With flashing: 42”) Height: 20” (With flashing: 30” or 32”) (depending on which size of flashing used) Depth: 22 .” In fireplace: 11 .” Weight: 185 lbs. Flashing: 13 lbs. Flue s

Ashes must be disposed in a metal container with a tight lid and placed on a no combustible surface well away from the home structure. · This stove must be connected to a standard 120 V., 60 Hz grounded electrical outlet. Do not use an adapter plug or sever the grounding plug. Do not route the electrical cord underneath, in front of, or over the stove. · The exhaust system should be checked, at a minimum, at least twice a year for any build up of soot or creosote. · Keep foreign objects out of t