Table 2. Replacement Parts Available for the Oxygen Therapy Door Form No. 702703 Rev. E August, 2006 17 Chapter 4 - Repairs and Replacements General Information Parts Ordering Procedure • Many of the threaded fasteners used on SSCI products are secured with thread adhesive to insure structural integrity. Removing any screw or bolt may be difficult at first. • During disassembly, retain all hardware items such as screws, nuts, lockwashers, etc. for reassembly. • If you have problems with any proc

16 Clear Polycarbonate Cleaning Procedures ..................................................................... 16 Ice Tray Cleaning Procedures ....................................................................................... 16 Nebulizer Cleaning Procedures ..................................................................................... 16 Chapter 4 - Repairs and Replacements....................................................17 Replacement Parts ....................................

wrench, remove the two gauge bracket screws/nuts (Figure 24). 3. Remove the gauge bracket and the gauge from the inside of the oxygen door. Gauge Bracket Screws Gauge Bracket Bracket Gauge Figure 24. Front View of the New-style Figure 25. Rear View of the New-style Gauge (mounted on door) Gauge (removed from door) Installation of New-style Gauge 1. Order the following from SSCI: • New-style Gauge - P/N 854771 • Gauge Bracket -P/N 600162-2 Note: Order a new gauge bracket only if replacing an old-

702703 Rev. E 08/06 Warning: Oxygen is a highly combustible gas. Avoid the use of open flames, smoking materials, or equipment capable of producing sparks in any area in which oxygen is being used. © Copyright 2006 by Suburban Surgical Co., Inc. All rights reserved. No part of this document may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system without written permission. Inquiries

Example: Push the oxygen supply hose onto the new fitting. Note: A small amount of grease on the barbs will ease assembly. WARNINGS Under the WARNING: headings, you will be alerted to potentially hazardous conditions which, if ignored or mishandled, could result in injury to yourself, or damage to the equipment. Example: WARNING: Oxygen is a highly combustible gas. Avoid the use of open flames, smoking materials, or equipment capable of producing sparks in any area in which oxygen is being used.

Carefully inspect your Oxygen Therapy Door while you unpack it. If damage is noted, or if parts appear to be missing, call SSCI Customer Service at (800) 323-7366. The following parts are included in the shipment (Figure 1): • Oxygen Therapy Door • Ice tray with valve • Nebulizer with supply tubing Oxygen Therapy Door Ice Tray With Valve Nebulizer With Supply Tubing Figure 1. Parts Included in Shipment Installation and Setup Tools Required • Phillips screwdriver • Punch (1/4 in. dia. max.) • Sma

Max/Min Button Clear Button Front View of Gauge Figure 13. Changing Between °C and °F °C / °F Slide Switch Rear View of Gauge Figure 12. Gauge Buttons Changing Between °C and °F Displays Replacing the Gauge Battery A slide switch on the side of the gauge (Figure 13) allows you to select between °Centigrade and °Fahrenheit temperature readings. Slide the switch UP to select °Centigrade; and DOWN to select ° Fahrenheit. The gauge is powered by a 3.0 volt, lithium, Type CR2032 battery which you can

H 91.44 cm W x 91.44 cm H 750831All 4 Sides 750909Top/Bottom 750831R & L Sides 4 12155-00-FNHJANew P/N: 102575-1Old P/N: 48 in. W x 36 in. H 121.92 cm W x 91.44 cm H 2 2 Table 4. Seal Strip Part Numbers SSCI - Suburban Surgical Company, Inc. Owner’s Manual - Oxygen Therapy Door Chapter 5 - Troubleshooting Warning: Oxygen is a highly combustible gas. Avoid the use of open flames, smoking materials, or equipment capable of producing sparks in any area in which oxygen is being used. Before servicin