You can get this free disc drive installation software from our web site at or run the program directly from your web browser. In either case, you should run DiscWizard before you install your drive. To run DiscWizard: Follow the instructions on the download page at to create a diskette and complete the installation. If you cannot run DiscWizard, follow the instructions on this installation sheet to install and configure your drive. What you need • A Phillips screwdriver and four 6-32 UNC drive

29 N drives section ......................................................................... 36 W/WD drives section .................................................................40 WC/DC drives section................................................................45 ©1997 Seagate Technology, Inc. All rights reserved Publication Number: 77767492, Rev. B January 1997 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology, Inc. Barracuda, SeaFAX, SeaF

The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data. The following conditions are considered DST failure conditions: • Seek error after retries are exhausted • Track-follow error after retries are exhausted • Read error after retrie

Cheetah 10K.7 SCSI Product Manual, Rev. D Table 15: LW 68-conductor LVD P cable signal/pin assignments [11] Note. Note: A minus sign preceding a signal name indicates that signal is active low. Signal name [1] Connector contact number [3] Cable conductor number [2] Connector contact number [3] Signal name [1] +DB12 1 1 2 35 –DB12 +DB13 2 3 4 36 –DB13 +DB14 3 5 6 37 –DB14 +DB15 4 7 8 38 –DB15 +DBP1 9 39 –DBP1 +DB0 6 11 12 40 –DB0 +DB1 7 13 14 41 –DB1 +DB2 8 15 16 42 –DB2 +DB3 9 17 18 43 –DB3 +DB4

2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the autodetect option and enable it. If your drive has a problem, it may not be recognized by the system. 3. Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system. 4. Does Scandisk find the drive defect-free? Scandisk is a utility located on you

Wenn Sie das Systemgehause nicht an die HDA/PCB- Erdung anschlie.en wollen, mussen Sie das Laufwerk auf nichtleitende Weise (galvanisch isoliert) im Host-Sys Barracuda 4LP Installation Guide, Rev. B tem einbauen. Die daraus u.U. resultierende verstarkte elektromagnetische Strahlung fallt in den Zustandigkeitsbereich des Systemdesigners. 5. Replace the host system’s cover. 5. Setzen Sie das Gehauseoberteil des Host-Systems wieder auf. Barracuda 4LP Installation Guide, Rev. B [4] A F D E L [1] [3]

Do not drop or jar the drive. Handle the drive only by the edges or frame. • Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground. • Turn off the power to the host system during installation. • Do not disassemble the drive; doing so voids the warranty. Return the entire drive for depot service if any part is defective. • Do not apply pressure or attach labels to the drive. Setting the jumpers Refer to the ju

• Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interOptions jumper block face bus. To enable cable select, set a jumper on pins 5 and 6. • Alternate capacity jumper: Drives with a 40-Gbyte capacity or greater are limited to 32 Gbytes. Use this jumper only if you have a legacy system with a BIOS that does not support large capacity disc drives. When using the alternate capacity jumper, • Manager software is

If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 1080sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Introduction .. .. .. .. .. .. .. .. .. .. .. .. . 1