from the wall in order to provide sufficient clearance for the blades. • In bedrooms, fans work best when mounted above the foot of the bed. • Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues. 7. MINIMUM 32° BLADES MUST BE A MINIMUM OF 7. ABOVE THE FLOOR EXTENSION POLE MAXIMUM HANG-TRU® ANGLE 32. • In low ceiling locations, our optional low ceiling adaptor (LCS) - available at extra cost can be used to gain 31/2. (not applicable to Stealth series). • In kit
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CONTROL FEATURES: INTELI•TOUCH OPERATION . . . . . . . . . . . . .
Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet RIDGE box. SIDE Tighten the screws firmly by hand only, being careful not to CEILING DOWN WIRING bend the bracket by over tightening. CAUTION: To reduce the risk of CROSSBAR personal injury, use only the MOUNTING mounting hardware provided with BRACKET the approved outlet box to install the crossbar mounting bracket. APPROVED OUTLET BOX HARDWARE GREEN GROUND
Turn the OFF for at least three seconds. 2. Turn the ON. 3. Immediately operate the buttons in the following sequence: + + + 4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours. To cancel the Light-Minder Program, turn the off for three seconds. INTELI•TOUCH OPERATION SAFE-EXIT® PROGRAM The Safe-Exit Program gives you abou
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo buttons (in that order). Note: You may want to label your controls to assure you do not mix them up. WARNING: Do not turn the power off at the circuit breaker, then back on, for the previously installed Versa•Touch fan(s), as you may inadvertantly change the frequency settings for it as well. DIP SWITCH DIP SWITCH SET TO ‘10000’ SET TO ‘01001’ 321 WITHIN 20 SECONDS OF TURNING THE FAN ON, PRESS IN THIS ORDER TO SET NEW FREQUEN
Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked ‘Approved for ceiling fan mounting’. If it is not, a new box must be installed. CROSSBAR MOUNTING BRACKET INSTALLATION WARNING: Damp Location rated fans require a Ground Fault Interrupter (GFI). Use a weather-proof outlet box, properly connect ground wires, and u
Danger of electrocution. Risk of scalding. APPLICABLE STANDARDS The products have received the “CE” certificate in accordance with the standards prevailing in different countries (European Directives 92/42/EEC, “efficiency”, 90/396/EEC “gas appliances”). These products have also received the Belgian “HR+” (gas boilers) marks. WARNINGS These instructions are an integral part of the equipment to which they refer and must be supplied to the user. The product must be installed and serviced by qualif
PROBLEM INTELI•TOUCH POSSIBLE REMEDIES.. NO FAN OR LIGHT Check main circuit fuses, curcuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. FAN WOBBLES OR SHAKES Be sure canopy pin is properly set into the slot on the ball EXCESSIVELY Check the screws holding the blade holders to the fan motor. Tighten as necessary. Check the angle of the blades to make sure that a blade holder has not been bent during installation. FAN NO
6. Check that the electrical connection and boiler room ventilation conform to the relevant standards. 7. Switch the on/off switch to the ON position. 8. Set the temperature settings (see pages 15-16). 9. Check the gas supply pressure (see page 13). 10. When the burner operates, check the chimney connection for leaks. 11. After 5 minutes of operation, turn the boiler off and vent the heating circuit system again maintaining the water pressure at 1 bar. 12. Then restart the unit and check the com