4. The user is responsible for all labor costs associated with removing, reinstalling and returning the product to Linear LLC. Linear LLC, at its option, will repair or replace the defective product. Replacements will be made from B-Stock, if an exact replacement is not available, Linear LLC, at its option, will select the nearest equivalent product. The user is responsible for freight charges to Linear LLC. Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent

Make sure gasket is behind camera Add top screws 3 2 Prepare the CAT-5 wires by stripping 1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws. Insert camera at an angle and rotate into place. * multiplex technology, inc. ® * * * 3001 Enterprise Street, Brea, CA 92821-6213, U.S.A. 714-996-4100 800-999-5225 FAX 714-996-4900 TM ChannelPlus® Video Cameras Models H722 & H722C ChannelPlus Enclosures, Modules, Accessories & Wall Plates ChannelPlus m

Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter © 1999 Out Incoming CATV or to TVs antenna coax Installation Step Two The wall plate Run a line of Cat and connect wires note: When using quad wire connect wires only to pins 1, 2, 5 and 6. Leave the resistor in place at pins 3 and 4. At the c

Position first pair to channel closest to end of jack. (Do not untwist conductor pairs more than 0.5" from the termination point.) Keep sheath close to jack. 1 Using a 110 punch-down tool, push wires into channels Repeat for subsequent pairs. and trim. 110 punchdown tool 2 When all conductor pairs are terminated, snap on strain relief caps. 3 Wiring Modular Plug (T568A) Wiring a Cat-5 jack Keep sheath close to connector Untwist .5” max. 110 punch down tool The 110 is a sophisticated insulation d

The channel injector designed to mount indoors or outdoors close or antenna feed. The system uses the existing in the house. The CatCam was designed to work with Cat 5 wiring. system will function with quad wire, Cat 5 delivers the picture. The Cat 5 allows the use of an automatic line length and picture compensator. Quad wire does not take advantage of this enhancement. Model Differences: The model 9500HHR series is a high headroom design for CATV and off air antenna feeds only. (5-806MHz) The

(NOTE: The C-BCK will not work if your cable company has filled then entire TV spectrum to CATV channel 125.) [ I 38 I WH0 eEJy Video distribution system with modulators JL SB msN 3S \\ Example: Modulator set to UHF 25. Tune TV to channel 3 to watch cable (select channel using set-top box) [C3D LIMITED WARRANTY STATEMENT Linear LLC warrants this product to be free from defects in material and workmanship for 2 years. The time period will be measured using the date code labeled on t

Channel At the channel connect Cat color coding on blue/white pin 1 © 1999 When using only quad wire use positions 1, 2, 5 and 6 and follow color coding. green pin 1 run the Cat 5 wire through the grommet at the bottom of the injector Applying Power and Programming Step Three The 9500 series has three different methods for applying to the system. Use only one method for applying power. Method One: Apply power directly to the channel injector with the power supply. power supply Power plug © 1999

Before Out to TVs Incoming CATV or antenna coax Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench. After Mount the injector within 4” of the splitter Supplied coax jumper goes back to splitter Out Incoming CATV or to TVs antenna coax © 1999 Installation The camera wire from the shown. prepare the Cat 5 wires stripping 1” of outer sheath and 1/8” of insulation insert the 6-32 screws into frame and bottom holes of gang box gasketframe

warrants this product to be free from defects in materials and workmanship for a period of one year from the date of purchase or MTI will repair, or at its option, replace the defective product. To obtain warranty service, call MTI for a return material authorization (RMA) number and return the product prepaid to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, CA 92821, Attention: Customer Service. Please put the RMA number on the outside of the carton. Any implied warranty arising fro

may void the user's authority to operate this equipment. The ChannelPlus SVS-52 is a five input audio/video selector. The SVS-52 has inputs for S-video, composite video, analog audio and digital audio. The selected video output is available on two separate but equal outputs. The SVS-52 also has video convertion for viewing S-video on composite or viewing composite video on Svideo. Aremote control is included for easy input selection. FRONT PANEL CONTROLS: 2 VIDEO SELECTION S-VIDEO/COMPOSITE SELE