However, proof of purchase in the form of a sales receipt or other information deemed suffi cient by MILWAUKEE, is requested. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES,

No de Cat. 48-59-1801 Battery pack and charger are not compatible with V ™-technology or NiCd systems. New battery packs must be charged before fi rst use. Le bloc de batteries et le chargeur ne sont pas compatibles avec les systemes NiCd ou de technologie V ™. Les batteries neuves doivent etre chargees avant leur utilisation initiale. El cargador y la bateria son incompatibles con la tecnologia V ™ y los sistemas NiCd. Las baterias nuevas se deben cargar antes de usarlas por primera vez. OPERAT

Return the tool and a copy of the purchase receipt or other proof of purchase to a MILWAUKEE Factory Service/Sales Support Branch location or MILWAUKEE Authorized Service Station, freight prepaid and insured. This warranty does not cover damage from repairs made or attempted by other than MILWAUKEE authorized personnel, abuse, normal wear and tear, lack of maintenance, or accidents. The warranty period for V28 Battery Packs is two (2) years from the date of purchase. The warranty period for Ni-C

Hammering Only Spline Drive System (Cat. No. 5318-21) When a chisel (or other “hammering-only” accessory) is mounted into the 5318-21 Rotary Hammer, the rotational drive mechanism does not engage with the chisel. Starting and Stopping the Tool 1. To start the tool, pull trigger. 2. To stop the tool, release trigger. Cold Starting If this tool is stored for a long period of time or at cold temperatures, it may not hammer initially because the lubrication has become stiff. To warm up the tool: 1.

Unplug the tool before changing accessories or making adjustments. WARNING Selecting Speed The speed control dial on these hammers allows the user to adjust the rotating speed (RPM) and the impact rate (BPM) of the tool. To change the speed, set the speed control dial to the desired setting. • Lower speeds provide more control when starting holes and reduce 'spalling' on breakthrough. Spalling occurs when pieces of material chip off around the drilled hole on breakthrough. When chiseling in soft

Una presion demasiado fuerte puede sobrecargar el motor de perforacion y puede causar que los diamantes se desgasten prematuramente, especialmente cuando se perfora acero incrustado. Haga que la broca trabaje, pero no intente meter a la fuerza la broca en el material. Si existe vibracion: 1. Detenga la taladracion. 2. Apague el motor. 3. Asegurese que no existan pernos, tuercas o tornillos prisioneros sueltos. Aprietelos si es necesario. 4. Revise la broca. Reemplacela si es necesario. Si la vib

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to fi lter out microscopic particles. 2 6 Capacities Drilling in Wood 1/2" Driving Screws 1/4" Using the Adjustable Clutch This tool has an adjustable clutch for driving different types of screws into different materials. When properly adjust

most be furnished to obtain correct parts. 72-1001 bul.54-06-0100 REVISED BUI 672-1 _) DATE FEB. ’68 WIRING INSTR. ILLUSTRATED PARTS Item Part No. Name of Part Item Part No. Name of Part 1 lA" Chuck H* 331-1 Handle Cover 2 25W8-1 Chuck tTasher 15 831-3 Cord Clamp 3 25VT-11 Spindle Gear 16 25W-28 Cord Protector Tube U 25*-8 Spindle 17 3B1-2 Switch Trigger 5 7057 Spindle Ball Bearing (rear) (1) 18 2517-1 Motor Housing 6 5137 Tru-Arc Spindle Retaining Ring 19 See Item 12 7 25W