Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to fi lter out microscopic particles. 2 6 Capacities Drilling in Wood 1/2" Driving Screws 1/4" Using the Adjustable Clutch This tool has an adjustable clutch for driving different types of screws into different materials. When properly adjusted, the clutch will slip at a preset torque to prevent driving the screw too deep and to prevent damage to the screw or tool. To adjust the clutch, turn the clutch adjusting ring so that the desired setting (1-15) lines up with the arrow on the motor housing, as shown. Fig. 2 Fig. 3 Driving Drilling The torque specifications shown here are approximate values obtained with a fully charged battery pack. in. lbs. Clutch Setting Applications 2 4 6 4 7 10 Small screws in softwood. Medium screws in softwood or small screws 8 10 13 16 in hardwood. Large screws in softwoods. Medium 12 19 screws in hardwood or large screws in hard14 41 wood with pilot hole. Drill 120 NOTE: Because the settings shown table are only a guide, material to test the clutch settings before driving Using Control Switch The control switch may be set to three positions: forward, reverse and lock. Due to a lockout mechanism, the control switch can only be adjusted when the ON/OFF switch is not pressed. Always allow the motor to come to a complete stop before using the control switch. For forward (clockwise) rotation, push in the control switch from the right side of the tool. Check the direction of rotation before use. For reverse (counterclockwise) rotation, push in the control switch from the left side of the tool. Check direction of rotation before use. To lock the trigger, push the control switch to the center position. The trigger will not work while the control switch is in the center locked position. Always lock the trigger or remove the battery pack before performing maintenance, changing accessories, storing the tool and any time the tool is not in use. Forward -Push from RIGHT Lock -Push to CENTER Fig. 4 6 Battery Pack Protection To protect the battery from damage and extend its life, the tool's intelligent circuit monitors current draw, temperature, and voltage drops. In extremely high torque, binding, stalling, and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash, and then the tool will turn OFF. To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery could become too high. If this happens, the fuel gauge will flash and the battery pack will shut off. Let the battery pack cool and then continue work. APPLICATIONS To reduce the risk of electric shock, check work area for hidden pipes and wires before drilling or driving screws. WARNING This tool provides a quick, convenient means of drilling small holes and installing and removing screws. Because of the many screw sizes, types, thread engagements and materials available, it is difficult to limit the application of this tool by screw size. However, for applications in wood, a #6 wood screw with a full pilot hole is recommended as a practical limit. Drilling in Wood, Composition Materials and Plastic Always use sharp bits. When using twist drill bits, pull the bit out of the hole frequently to clear chips from the bit fl utes. To reduce the chance of splintering, back work with a piece of scrap wood. Select low speeds for plastics with a low melting point. Driving Screws Drill a pilot hole when driving screws into thick or hard materials. Set the clutch adjusting ring to the proper position and set the speed to low. Use the proper style and size screwdriver bit for the type of screw you are using. With the screwdriver bit in the screw, place the tip of the screw on the workpiece and apply firm pressure before pressing the foward/reverse switch up. Screws can be removed by pressing the foward/reverse switch down. Locking the Screwdriver Bit When the tool is off, the screwdriver bit automatically locks in place allowing to use the screwdriver manually. Do this to tighten screws that require than the driver is capable of confirming the tightness of a loosening an extremely 7 Reverse -Push from LEFT MAINTENANCE WARNING To reduce the risk of injury, always unplug the charger and remove the battery from the charger or tool before performing any maintenance. Never disassemble the tool, battery or charger. Contact a MILWAUKEE service facility for ALL repairs. Keep your tool, battery and charger in good repair by adopting a regular maintenance program. After six months to one year, depending on use, return the tool, battery and charger to a MILWAUKEE service facility for: • Lubrication • Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.) • Electrical inspectio...