Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Remove all contents from the package and check for completeness (see itemized table and picture). NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Spray head 3 Counter weight and gaskets 4 Fastening set (rubber washer, triangular flange, metal washer, threaded nut) 5 Hexagonal wrench 6 Valve-holder 2/8 2. Remove all mounting hardware from protective plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into the desired location NOTE: The rubber O-ring should be sitting on top of the countertop and between the faucet body. DO NOT use putty or other sealant at this location 4. Install the mounting hardware (GR0356031) to the threaded shank in the following sequence: 1 - round flat fiber washer 2 - triangular shaped plastic support 3 - flat metal washer 4 - thread brass nut 5. Assure that the handle and spout are properly aligned in forward position 6. Tighten the brass nut (4) with the provided wrench or use other professional tools. NOTE: Solid surface installation: The sub-countertop mounting surface needs to be flat and free of debris; otherwise the faucet will not sit properly. Tile installation: Avoid installations near or on top of grout lines. The faucet will not sit secure when sitting on such. Insert the spray hose (WITHOUT HEAD) into the faucet spout and pull it all the way through. 3/8 7. Attach the valve-holder to the shorter tubing and attach the spray hose to the valve-holder. NOTE: The provided small black rubber washer needs to be installed here. DO NOT use putty or other sealant agents at this joint. 8. Attach approved connector hoses to the two longer copper tubes and connect to water supply valves. WARNING! Do not allow the supply tubes to twist or bend sharply. NOTE: It is recommended to use approved stainless steel braided supplies. 9. Flush out debris from water lines and faucet. 1. Pull spray hose out of the faucet spout and point the open end towards the sink drain. 2. Open faucet handle - cold side first - by turning handle to the right and moving it upward 3. Let the faucet run on cold for 15 to 30 seconds. 4. Open faucet handle - hot side second - by turning handle to the left and moving it upward. 5. Let the faucet run on cold for 15 to 30 seconds. 6. Turn faucet off. 7. Test for leaks under the cabinet. 4/8 10. Assemble Pull-out Spray. 1. Attach the pull-out spray head to the hose. NOTE: The rubber washer needs to be installed to prevent leakage. 400 mm 400 mm 2. Fasten the weight to the hose as shown in picture below.. 3. Test all water lines, fitting and connections for leaks. 5/8 Standard maintenance and trouble shooting Cleaning of the spray head Any deposits which may accumulate on the nozzle can be removed by simply running a finger over the rubber extrusions and then running the water for a few seconds. In extreme cases this step may have to be repeated. Replacing the Cartridge 1. Shut off the water supply to the faucet. 2. Open the faucet briefly to relief any pressure inside the faucet. 3. Move the faucet handle to the “OFF” position. 4. Use a the provided allen key to loosen the set screw which is accessible from the back of the handle. 5. Lift the handle from the cartridge. 6. Find the small notch at the base of the chrome ring cap and carefully pry up against this to remove the cap. 7. Remove the brass retaining ring. 8. Lift out the cartridge. 9. Ensure that the seats and O-rings are in good condition 10. Remove potential mineral deposits from inside the faucet body. 11. Install the new cartridge so that the central pivots fit into the corresponding seats. 13. Re-assemble faucet in reverse order. 14. Test for leakage. 6/8 General maintenance Clean aerator periodically. Do not use harsh detergents, solvents, chemical agents, steel wool, etc. that could harm the surface. Clean only with a soft sponge and soapy water. In the case of very hard water, it is necessary to clean and dry the faucet after each use. Calcium deposits could damage the surface. 7/8 Limited lifetime warranty Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the original purchaser of its faucets effective January 1, 2003. All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical parts to be free of manufacturing defects in material and workmanship under normal usage. All chrome finishes carry a limited lifetime warranty; all other finishes are warranted for five (5) years form the original date of purchase. Marine Installation: All products in a marine installation will carry a limited lifetime warranty on all mechanical parts to be free of manufacturing defects in material and workmanship under normal usage. All chrome products carry a limited lifetime warranty on the finish; all other finishes carry a three-year (3) warranty from the original date of purchase. This warranty applies only to t...