(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-1600 Series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Inlet connections: 1/2. NPSM Please read our instruction before you

Such damage is not covered by the warranty] Water is not hot: Check if electrical supply to heating tank is plugged in. Turn temperature control knob clockwise as far as possible. Test the temperature again after 15 minutes. Check if fuse is blown or circuit breaker is open. Hot water continuously drips or sputters from spout: For safety reasons this faucet may drip or splutter after use. This venting prevents a build-up of pressure in the heating tank. If this becomes excessive; Turn the

Davlumbaz Uzivatelska Poirueka Odsavac par FDB 9078 SIL-K INDEX EN RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS ............................................................................................................................................................. 4 INSTALLATION.............................................................................................

W9223028 For use in Filter Model No. FRCNSTR/ FRC05 The system is tested for the following performance claims as verified and substantiated by test data: • Chlorine Reduction (Taste & Odour) • Particulate reduction; • Turbidity reduction; • Cyst reduction (including Giardia and live Crypto-sporidium); Systems tested for Cyst Reduction may be used on disinfected water that may contain filterable Cysts. Do not use where water is microbiologically unsafe or of unknown quality without adequ

14. Test for leakage. 5/7 General maintenance Clean aerator periodically. Do not use harsh detergents, solvents, chemical agents, metallic sponges, etc. that could harm the surface. Clean only with a soft sponge and soapy water. Clean and dry the faucet properly in case of hard water deposits which could damage the surface. Replacing the spray flex hose 1. Shut off the water supply to the faucet. 2. Pull the spout outwards from its place and unscrew the aerator . 3. Unscrew the hand shower from

These include pre-filter and carbon cartridges. Filter cartridges are easily replaced by removing the stainless steel cartridge housing’s cap. This automatically shuts off the water supply and allows the new cartridge to be inserted quickly and cleanly. It is recommended that a new cartridge is used every 6-12 months according to water quality. Any noticeable reduction in the filtered water’s flow rate usually indicates a new cartridge is required. Franke Uniftow and Little Butler™ Systems wor

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROvAL OF GRIzzLY INDUSTRIAL, INC. #TS11344 PRINTED IN TAIWAN

(1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Flexible hose of the side spray 3 Hook for side spray 4 Side spray 5 Priority water flow system 6 Fastening set (rubber washer, metal washer, nut) 7 Fastening set (rubber washer, triangular flange, metal washer, nut, allen key 2,5mm) 8 Counter weight 3 ENGLISH Install faucet to the sink or countertop Set the faucet into place on the sink as indicated in the figure. NOTE: the rubber O-ring should be sitting on top of the count

The dispensing head comes with three 1/4” copper tubes and one silicone tube. The two shorter (12”) copper lubes are connected to the incoming water supply via the canister. The supply to the cold side may be diverted through a chiller before the dispensing head, if required. The longer (18”) copper tube is connected to the inlet of the tank. The silicone tube is connected to the outlet of the tank using the hose connector. Preparing for the Installation As with any sink related device, it is

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-3000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Tailpipe connections: 3/8. O.D. Please read our instruction before