Advocate® 70 CS User Guide IMPORTANT:Thoroughly read and follow all instructions before installing this child seat. Store this user guide in the pocket behind the cover (See features pages for reference). Table of Contents Table of Contents Safety Information.......................................................................................2 Warnings...............................................................................................................2 Important Notes................

The base can remain in the vehicle during visual inspection of carrier. Turn carrier upside down so the underside of the carrier faces upward. If one or both tabs do not fully cover the opening, contact Britax Child Safety, Inc. at 888-427-4829 for further instruction. If both tabs are not fully covered, you may continue to use the carrier in vehicle without the base. On bottom of carrier where rubber strips run along edges of support rails, there is an exposed opening with attachment hooks.

33IMPORTANT: • The harness buckle strap should lie toward the back of the child seat during installation. • The buckle should be in the inner slot for rear-facing installation. 34 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow, unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. IMPORTANT: Ensure bu

All rights reserved. Printed in USA P464800_R1:03.11 This product and its components are subject to change without notice. Section TitleWARNING! DEATH or SERIOUS INJURY can occur: WARNING! DEATH or SERIOUS INJURY can occur: • Harness mode: use only with children who weigh between 25 and 85 lbs (11.3 and 38.6 kg) and whose height is between 30 and 57 in. (76.2 and 144.8 cm) and are at least 2 years of age. • Booster mode: use only with children who weigh between 40 and 120 lbs (18.1 and 54.4 kg)

Doing so could cause the child seat not to perform as intended. Forward-Facing Installation Forward-Facing Installation 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Route the vehicle seat belt through the forward-facing belt slots, then buckle. Ensure the vehicle belt is not twisted. 5 Push the

E). • If your vehicle is equipped with an automatic locking retractor (ALR), use of lock-offs is not required as long as ALR is activated. Check your vehicle’s owner’s manual to determine type of retractor your vehicle has, and for proper use of retractor. 8Verify all connections are secure and restraint is stable. The restraint is secure when it cannot be moved front-to-back or side-toside more than 1” (2.5 cm.) at belt path. If restraint is not secure, repeat procedure or use an alternate seat

Removal • If connected, disconnect the Versa-Tether® from the tether anchor. • Release each LATCH harness from the LATCH anchor by pressing the red release button on the LATCH connector. • When not in use, always store the LATCH connectors in storage pouches sewn in cover above rear-facing lock-offs. D E 11 Installation: Rear-Facing Lap-Shoulder Belt Installation • Figure A illustrates a typical rear-facing lap-shoulder belt installation. • When not in use, always store the LATCH connectors in s

Your statutory rights are not affected by this guarantee. Britax Excelsior Limited 1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom A Britax Childcare company Customer Service Helpline: 01264 386034 Email: helpline@uk.britaxeurope.com Switchboard: 01264 333343 Fax: 01264 334146 Britax, whilst taking into account child car seat contact with vehicle seats throughout the development of new products, cannot accept responsibility for damage occurring to vehicle seats or seat belts. IMPO

Check wheels are fully engaged by gently trying to pull them out. Hold handle and lift upwards until stroller frame is fully extended and clicks into position. Push front swivel-wheel assembly into front leg. Listen for a positive “click” to ensure the wheel is correctly fitted. When properly fitted, the screw head on the front swivel-wheel assembly should face forward and the wheel’s solid spoke fronts should face outward. Pull down gently on the wheel to ensure it is fully engaged. Repeat proc

8 Vehicle Compatibility Incompatible Vehicle Seat Belts...................................................................................10 Vehicle Buckle Positions...............................................................................................11 Vehicle Seating Positions..............................................................................................11 Installation: Rear-Facing LATCH Installation.......................................................................