A second press will turn the pump to high speed. A third press will turn the pump off. A buiit-in timer will shut the pump off after 20 minutes unless it has been manually deactivated. The "Pump" indicator light will be on when the Pump is running. "Pump" indicator light 38 -«•$>& % i t> • • • • ^ /V V I'uap light lip llown To turn the light on: Press the Light key to turn the light on. A second press will turn the light off. A buiit-in timer will shut the light off after 2 hours unles

The LED lights will automatically turn themselves off after 2 hours in any one setting. Neptune Series Spas feature an easy-to-change selection of nine different LED color/display settings. To activate the LED lights, press the "LIGHT" button on the topside panel one time. To advance to the next color/display setting, press the "LIGHT" button twice in a row. The LED's will go off with the first press, then back on in the next setting with the second press. If the LED's remain off for more than 5

Please call your local Dynasty Spa Dealer if you have any questions or problems. If they are unavailable, please feel free to call the Dynasty Spas Customer Service Group at: 800-951-6224. Dynasty Spas Operator’s Guide • TABLE OF CONTENTS OWNER’S INFORMATION ......3-4 FILTER MAINTENANCE ..........15 • Dealer Information • Installer Information • President’s Letter SAFETY INSTRUCTIONS ......5-6 • Warnings • Dangers BASIC INFORMATION ..............7 • Do’s and Dont's SET-UP AND DELIVERY GUIDELINES

"Mode" Key "Soft" Key 1, "Plus" Key increases selects mode of 2, 3, 4 "Ok" Key parameter setting operation: Spa, Operation Mode Menu title AM/PM (.F/ .C) L LLi iig ggh hht ttt icons Information Display "Right" Time, temperature Multi & message digits function Key Pump Progress bar icon icons "Left" Multifunction Key "Minus" Key "Next" Key goes to Status icons L LLo ooc cck kkk icon Service icon goes back to previous decreases par-menu page parameter setting or ameter setting increases parameter

The Priming mode will last for less than 5 minutes (press "Temp" or "Set" to skip Priming Mode) and then the spa will begin to heat the spa and maintain the water temperature in the Standard mode. Your system has a 24-hour circ pump. The circ pump and the ozone generator run continuously with the exception of shutting off for 30 minutes at a time in hot environments. Temp/Set (80°F - 104°F / 26°C - 40°C) The start-up temperature is set at 100F°/37°C. The last measured temperature is constantly d

Spa settings will be preserved until next power up. After the circ pump has been running for 2 minutes, the temperature will be displayed. DO NOT ENTER THE WATER. Remove the spa cover and allow water to cool. Once the heater has cooled, reset by pushing any button. If spa does not reset, shut off the power to the spa and call your dealer or service organization. DO NOT ENTER THE WATER. Remove the spa cover and allow water to cool. At 107°F/42°C, the spa should automatically reset. If spa does no

¦ Do not let the power cable hang over edges (trip wire effect). Inserting batteries into the remote control NOTICE The supplied battery (3V, type CR 2032) has already been fitted into the > remote control at the factory. Before use, remove the insulation strip from the battery compartment. To insert a new battery, proceed as follows: • Open the battery compartment at the rear of the remote control 9 by rotating the circular cover in the direction of the symbol . Use a small coin for turning it.

The default filter time is 2 hours. To program, press “Temp” or “Set,” then “Jets.” Press “Temp” or “Set” to adjust. Press “Jets” to exit programming. At the beginning of each filter cycle the blower purges for 30 seconds; the pump purges for 5 minutes. The only effect filter duration has is: 1) During the filter, the circ pump never turns off, and 2) In Economy and Sleep Modes, heating only occurs during the filter cycle. Freeze Protection If the temperature sensors detect a drop to below 44°F/

To activate the LED lights, press the "LIGHT" button on the topside panel one time. To advance to the next color/display setting, press the "LIGHT" button twice in a row. The LED's will go off with the first press, then back on in the next setting with the second press. If the LED's remain off for more than 5 seconds, the color/display sequence will reset and start back at the beginning the next time the "LIGHT" button is pressed. The color/display sequence is: Setting #1 LED's light up and slow

Not a bug but a feature! Our Smart Winter Mode protects your system from the cold by automatically turning the pumps on for one minute several times a day to prevent water from freezing in pipes. Water temperature is displayed. Water temperature in the spa has reached 112.F (44.C). Do not enter the water! Allow water to cool down. The system will reset au- tomatically when water reaches 109.F (43.C). Call your dealer or service supplier if problem persists. 3 flashing dots are dis- played. A pro