Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
¦ Do not let the power cable hang over edges (trip wire effect). Inserting batteries into the remote control NOTICE The supplied battery (3V, type CR 2032) has already been fitted into the > remote control at the factory. Before use, remove the insulation strip from the battery compartment. To insert a new battery, proceed as follows: • Open the battery compartment at the rear of the remote control 9 by rotating the circular cover in the direction of the symbol . Use a small coin for turning it. • Insert a battery of the type CR 2032 (3V) into the battery compartment. Make sure the polarities are correct; the positive pole faces up. • Close the battery compartment by replacing the round cover and turning it in the direction of the symbol until it is firmly seated back in the housing. Fixing the air-bubble mat into the bath DANGER Slippery! If the air bubble mat is not fixed into the bathtub properly, there is a great risk of slipping! Observe the following safety information to avoid the risks of slipping: Carefully press the air-bubble mat onto the bottom of the bath tub until all > of the suction cups on the air-bubble mat are firmly secured to the bath bottom. Check every time before getting into the bath tub whether the air-bubble > mat is still properly and firmly secured. Do not climb into the bathtub before all the suction cups of the air-bubble > mat are properly secured in the bath tub. SLB 450 A1 9 Setting up and connecting GB IE CY • Place the air-bubble mat 6 onto the bottom of your bath tub so that the connection-support for the air hose 7 is pointing upwards. • Press the air-bubble mat 6 with the flat of your hands until it is firmly secured onto the bath tub floor by its suction cups. NOTICE The suction cups of the air-bubble mat attach themselves to the bottom of > the bath tub much easier and more firmly if you first moisten them slightly before pressing. Using aromatic oils Optionally, you can use aromatic oils (perfume or massage oils). For this, use the supplied aroma-oil pad 11. 11128 11. • Open the aroma-oil pad • Place a few drops of aromatic oil onto the cotton fleece 12 and replace the fleece into the aroma-oil pad 11. • Close the aroma-oil pad 11. • Place the aroma-oil pad 11 in the pump side connection-support of the air hose 8. SLB 450 A1 10 Setting up and connecting GB IE CY Connecting the air hose • First connect the air hose 8 to the connection-support 2 of the pump . With this, ensure that the plastic cam aligns exactly with the recess in the 2connection-support . • Then turn the hose connector of the air hose 8 to the left, in the direction of the symbol , until the hose connector is clamped in the connecting support 2 of the pump . 28 ..Afterwards, insert the hose fitting on the other side of the air hose 8 firmly into the connection-support of the air-bubble mat 7. 87 SLB 450 A1 11 Handling and operation GB IE CY Electrical connections DANGER Risk of fatal electrocution! Contact with wires or components carrying mains power could be potentially fatal! Observe the following safety notices to avoid risks from electrical hazards: Do not operate the appliance if the power cable or the plug are damaged. > Connect the appliance only to an electrical outlet protected by an FC > protector switch (RCD) with a rated residual current not exceeding 30 mA. Never touch the pump and the mains plug with wet hands. > Avoid water contact with the pump. > Place the pump at least 60 cm away from the bath tub. > Under no circumstances should you open the housing of the appliance. > Should live connections be touched and/or the electrical and mechanical construction changed, there is a risk of receiving an electric shock. Insert the plug into a mains power socket. .. Handling and operation In this chapter you receive important information for the handling and operation of the appliance. NOTICE Before using the equipment, make sure the room temperature is right. > The bathroom temperature should not be lower than 25°C. Switching On and Off Switch the pump on with one press of the function button 3 on the pump. Switch the pump off with several presses of the function button 3 on the pump. SLB 450 A1 12 Handling and operation GB IE CY NOTICE In the same way, the pump may be switched on or off using the remote > control 9 by pressing the function button 10. Functions The appliance offers three different operating modes: ¦ Continuous with low intensity ¦ Continuous with high intensity ¦ Massage operation IMPORTANT Risk of damage to the appliance from excessive continuous operation. Excessive continuous operation may cause an overheating of the pump. The appliance switches off after 20 minutes usage time. > Allow the pump to cool down for 10 minutes after the normal period of use > before switching it back on. Function selection on the pump • Switch the pump 5 on with one press of the function button 3 . The LED operation indicator blinks green, and the pump is operating at the lowest level of intens...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - SLB 450 A16 (270.74 kb)