If you do not have this equipment, you can not service this tool. Hypot testing is a safety test required by Underwriter’s Laboratories. It basically ensures that there are no live metal parts exposed on the product. This condition could occur if, for instance: 1. A housing screw went through a wire. 2. A wire was stripped back too far and the bare wire contacted a bearing or the driveshaft. 3. A wire was damaged and came into contact with a bearing or the driveshaft. This is a very serious

Der Schaft des Schleifkegels muss nicht ganz eingeführt werden, wobei die Höchstspannlänge von 10mm nicht unterschritten werden darf -siehe Abbildung 2. Beachten, dass die erlaubte Betriebsdrehzahl des Schleifkegels sich Spannpatronenhalter Spannpatronenmutter Schleifkegel D = Durchmesser des Lo = Überhang Schlelfkegeis S = Durchmesser des Schafts T = Länge des Schleifkegels Lg = Spannlänge Abbildung 2. Spannlänge der Spannpatrone und des Spannfutters durch eine Verlängerung des Schafts

Der Drosselklappenhebel muss jederzeit beim Loslassen in die „Aus”-Position zurückkehren können, immer die Druckluftzufuhr zum Werkzeug ausschalten, und zum Ablassen der Luft aus dem Luftschlauch das „An/ Aus”-Ventil drücken, bevor der Arbeitsaufsatz am Werkzeug montiert, entfernt oder eingestellt wird. Alle Roehre und Anschluesse sollten einen Mindestdurchmesser von 12mm aufweisen Kompressor muss den empohlenen Arbeitsdruck am Lufteingang des Werkzeuges halten koennen flsn- ( Lufttank - \

It may also be used with steel rotary files and carbide burrs provided their speed rating matches or exceeds the speed of the grinder. This tool should not be fitted with cutting off wheels, saw blades, drill bits, etc. If there is any doubt about the correct use of this product contact your supplier for advice. Also, make sure that the shank size of the attachment to be driven marches the collet size fitted in the grinder and that the maximum allowed running speed of the attachment exceeds th

ImpactTool C? @ IMPORTANT Readtheseinstructionscarefullybefore installing,operating,servicing or repairingthis tool. Keeptheseinstructionsin a safeaccessible place. 11 I I I SAFETY MESSAGES 1 A WARNING 1 Operator Instructions PeoonalSafetyEqucment Always Read Instructions includes: 1 1 Use-Safety Glasses Using PowerTwls Safety Ruk Use -Safety Gloves @ AlwaysWear Safety Goggles Foreseen Use Work Stations Use-Safety Boots @ Wear Hearingprotection PuttingIntoService Use-BreathingMasks Avoid Prolong

etc. to make it rigid so it does not move during the work -The tool is not electrically insulated. Never use the tool if operation. Keep good balance at all times. Do not stretch there is any chance of coming into contact with live or overreach. electricity. -Try to match the tool to the work operation. Do not use a -Always when using the tool, adopt a firm footing and/or tool that is too light or heavy for the work operation. If in position and rip the tool sufficiently only to overcome doubt,

.. 1 SAFETY MESSAGES 1 A WARNING 1 Operator Instructions Personal Safety Equipment Always Read Instructions Before Includes: Use -Safety Glasses YES 1 @ Using Power Tools 1 Safety Rules Use -Safety Gloves YES (^ Always Wear Safety Goggles ores seen Use Work Stations Use-Safety Boots @ Wear Hearing Protection Putting Into Service Use -Breathing Masks YES A A Avoid Prolonged Exposure To Vibration Operating Use -Ear Protectors YES Dismantling and Assembly. Safety rules when using a 5264 & 5266 Need

No. Part No. Description 1 505372 Inlet Bushing with Screen 2 505709 Deflector 3 505371 O-RIng 4 505710 Valve Spring 5 505367 Valve 6 505366 Valve Pin 7 505365 Valve Seat 8 505713 Roll Pin 9 505867 Motor Housing 10 505868 Roll Pin 11 505869 Roll Pin 12 505870 Reverse Lever 13 505871 Spring 14 67202 Steel Ball 15 505711 Muflier 16 505714 Valve Shaft 17 505715 Trigger 18 67081 O-Ring 19 505872 Reverse Valve 20 505873 Ball Bearing Ref. No. Part No. Description 21 66570 Roll Pi

When first lubricating a tool or if the tool exhaust has a high oil content, do not allow the exhaust air to come near very hot surfaces or flames. -Never lay the tool down until the working attachment has stopped moving. -When the tool is not in use, shut off the air supply and press throttle triggerllever to drain the supply line. If the tool is not to be used for a oeriod of time. first lubricate. disconnect from air supply &d store in a dry average room temperature environment. -If the tool

1 SAFETY MESSAGES 1 A WARNING 1 Operator Instructions PersonalSafety Equipment Always Read Instructions Before Includes:1 YES 1 0 "sing Power Tools 1 Use -Safety Glasses Safety Rules Use -Safety Gloves @ Always Wear Safety Goggles ores seen Use Work Stations Use -Safety Boots @ Wear Hearing Protection Putting Into Service Use -Breathing Masks A T Avoid Prolonged Exposure o Vibration Operating Use -Ear Protectors YES Disrnantlina and Assernblv. Safety rules when using a 509215092L Impact Tool -Us