NOTE: it is normal for the Br Mono indicator LED to transition slowly. •STEREO MODE (Green LED). Each channel operates independently, as usual. •PARALLEL INPUT MODE (Orange LED). The inputs of both channels are hard-switched together, but all controls and speaker connections work as usual. Do not attempt to parallel the output channels to the same load. INPUT SENSITIVITY SWITCH, 3-POSITION: 26dB, 32dB, 1.2V •The 26dB (Orange) and 32dB (Green) settings provide the same voltage gain for all models

GAIN CONTROLS 21 Steps, 1dB Each. 6 QSC DATAPORT Supports QSC DataPort Products. HIGH PASS FILTER SWITCH (Ch1, Ch2) Off (No LED), 30Hz (Yellow), 50Hz (Orange) CLIP LIMIT SWITCH (Ch1, Ch2) Off (No LED), On (Yellow) XLR INPUT CONNECTORS Female and Male, Wired in Parallel for Daisychaining to Additional Equipment. Balanced Inputs, Impedance >10K Balanced: Unbalanced: PLUGGABLE TERMINAL BLOCKS 5.0mm, 3-pin. Paralleled with XLRs Balanced Pinout: Unbalanced Pinout: INPUT MODE SWITCH Bridge (Yellow) Se

3- Heed all warnings. 4- Follow all instructions. 5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this apparatus near water. 6- Clean only with a dry cloth. 7- Do not block any ventilation openings. 8- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

6. Measure the DC voltage across R147. Adjust bias trimpot R131 to reach the correct voltage shown in Table 1. 7. Next, measure the DC voltage across R247. Adjust bias trimpot R231 to reach the correct voltage shown in Table 1. 8. Turn off the amplifier and reattach the channel module assembly and heat sink to the chassis. Current limit adjustment Note: Read through these instructions before proceeding. To avoid tripping the amp’s circuit breaker, work carefully but quickly, and don’t run the am

Solder a new zener diode “piggyback”-style onto each old one. Procedure: Installing new zener diodes in an ISA 450 or ISA 500T amplifier 1. Disconnect the amplifier from AC and wait at least 10 minutes for internal voltages to bleed down. Remove the top cover. 2. Remove the four screws on the bottom of the amplifier that fasten the heat sink to the chassis. 3. Remove the three screws that attach the channel module assembly to the chassis standoffs. 4. Locate zener diodes D107 and D110 on the cha

Make sure your AC supply is appropriate for the amplifier. • 1 kHz audio sine wave generator D107 & D210: • Digital multimeter • AC current probe (e.g., BK Precision model CP-1) D207 & D110: • Trimpot adjustment tool (non-conductive) Note: The circuit boards in the ISA 750 and ISA 800T are double-sided, while those in the ISA 450 and 500T are single-sided. Therefore, to minimize disassembly, this bulletin Figure 1. Prepare the leads of the recommends two different procedures among these models:

This problem is most pronounced in the ISA 750 and ISA 800T models, but may also occur in some ISA 450 and ISA 500T amplifiers. Symptoms When the amplifier is turned on, one or both channels remain inoperative, with their respective clip LEDs lit. In some cases, the problem will clear by itself after several seconds. This problem is merely a nuisance and presents no danger to the amplifier, the speakers, or the rest of the sound system. Any one or more of these situations will tend to aggravate

Diese Garantie wird gelegentlich aktualisiert. Die jeweils aktuellste Version der Garantieerklarung von QSC finden Sie im Internet unter Sie erreichen uns telefonisch unter +1 800-854-4079 (gebuhrenfrei in den USA und Kanada) oder im Internet unter 1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA Zentrale +1 (714) 754-6175 oder gebuhrenfrei (nur in den USA) +1 (800) 854-4079 Kundendienst+1 (714) 957-7150 oder gebuhrenfrei (nur in den USA) +1 (800) 772-2834 © Copyright 2006, QSC Audio Products, In

HPR122i, HPR152i oder HPR153i 15 Anwendungsbeispiel 2 Dieses Beispiel zeigt eine Zweikanal (Stereo)-Anlage mit einem Subwoofer und zwei Top-Boxen. Audiosignale fur den linken und rechten Kanal werden vom Mischpult ausgegeben. Diese Signalquelle kann im Prinzip fast jede beliebige Audioquelle mit variablem Ausgangspegel sein, z. B. ein DJ-Mischpult, professionelle CD-Player oder computerbasierte Audiosignalquellen. Der Audioausgang vom Mischpult wird mit dem linken (L) und rechten (R) Kanal des S

Das Ausrufezeichen in einem Dreieck soll den Benutzer auf das Vorhandensein wichtiger Betriebs- und Wartungsanleitungen in diesem Handbuch aufmerksam machen. 1. Diese Anleitung sorgfaltig durchlesen. 2. Diese Anleitung gut aufbewahren. 3. Alle Warnhinweise beachten. 4. Alle Anweisungen befolgen. 5. ACHTUNG: Zur Vermeidung von Branden und Stromschlagen darf diese Ausrustung weder Regen noch Feuchtigkeit ausgesetzt werden. Dieses Gerat nicht in Wassernahe verwenden. 6. Nur mit einem trockenen Tuch