Note: Please read these instructions thoroughly before attempting to install this unit. SAFETY NOTICE: If this stove is not properly installed, a house fire may result, for your safety, follow the installation directions, contact local building or fire officials about restrictions and installation inspection requirements in your area. IMPORTANT: Check around oven chamber on a weekly basis for soot and creosote accumulation. Clean the chamber thoroughly from the top, side and bottom with the rake

Screw will back off enough to open door.It is not possible to open lower door without first opening upper door. (See Figure 2) To close the doors. Close both doors tight and use utensil to tighten both door release screws clockwise. Ensure both doors are secured tight so that no air will be able to fuel the fire through the fire doors. Do not slam the fire door shut! Lighting the Fire a) Check the flue pipe is free of blockage. b) Open firebox door. c) Open ashpit door. d) De-ash and remove dead

English Edition Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner Installation and Operating Instructions under Exhaust Hood section before completing this installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) Before proceeding, check for damage that may have occurred during shipping. If the contents are damaged, inform the freight company or your dealer immediat

For Model 9200 use 4 sheet metal screws and washers. To prevent chipping do not overtighten or use power tools. 5 WOOD STOVES ONLY STOVETOP Bracket -Place box on the floor close to stove. (See Fig. 1 Page 2). Machine screw Remove machine screws from the top (2 each side) Screwdriver -Remove the nuts, washers and screws located at rear edge of stove top (2 on SWEETHEART,4 on OVAL) and the 4 machine screws from the stove top. -With a helper, lift cabinet assembly from box by area that is circled.

-Remove small box and its contents. -Remove the cardboard cross brace. -Remove the plastic wrapped cresting panel. 2 Assembly of Cresting Panel. Main Cabinet Cresting PanelWingnut view of top of cabinet Locate cresting panel packed in bubble wrap. Unwrap the cresting panel and remove the wingnuts. Place the cresting panel on the rear of the top of the cabinet. Take the wingnuts and fasten the cresting panel to the cabinet through the holes at each end of the cabinet. For: WOOD STOVES - go throug

English Edition Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner Installation and Operating Instructions under Exhaust Hood section before completing this installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) Before proceeding, check for damage that may have occurred during shipping. If the contents are damaged, inform the freight company or your dealer immediat

-With a helper, lift cabinet assembly from box by area that is circled. (See Fig. 1 Page 2). -Place cabinet assembly onto stove body. (See diagram above). -Line up holes in the bottom (foot) of the bracket with the stove top holes while one person supports cabinet, fasten the cabinet brackets to the stove with machine screws (2 each side). (See diagram above). -Re-insert screws from the inside of the lip at the back of stove through the splashback , then assemble the nuts and washers to each scr

(NOTE: if your cupboards are too low the cresting panel may be left off). 3 ELECTRIC AND COMBINATION STOVES ONLY STOVETOP Gasket - Peel off backing and stick on. Bracket Sheet metaI screw (black) Steel Washer Machine screw (Nickel Plated) Gasket Machine screw Steel washer Sheet metal screw -Remember when working with the cabinet, the cabinet is top heavy. Use your hand to support it during installation. -Place box on the floor close to stove. (See Fig. 1 Page 2). -With a helper,lift cabinet asse

The bulb can then be unscrewed easily. Always handle the bulb with a dry (never wet) cloth to protect hands. If light bulb should break, disconnect power to range by unplugging it or removing the fuse from the panel before touching the bulb. When replacing the bulb, use only a 40 watt oven bulb available at your local hardware store or appliance dealer. When cleaning the oven, do not touch lens with a wet cloth. 27 Surface Burners Top burners require little care other than to wipe off the head o

Broil Diagram shows how element will not turn on when bake element is used. heat is radiated from the elements, during the cooking process Convection Cooking: Convection means conveying. A fan at the back of the oven circulates the hot air thus Convection Air Pattern cooking foods from all sides, sealing in juices. The circulating air penetrates food faster Diagram shows how heat is therefore you may want to cook foods for less time at the usual temperature or reduce circulated from the convecti