Avoid operating the engine at low speeds. Doing so can lead to rapid clutch wear. In addition, slow-speed operation tends to cause grass and debris to wrap around the cutting attachment. (1) After starting the engine, pull the throttle lever gradually. The engine speed increases and the blade will start rotating. (2) When the throttle lever is released, the engine goes back to idle speed automatically. (3) Operate the machine at full throttle while cutting. Best fuel efficiency is obtained by re

KOREAN /....... 1.... 1........................... ..................G . ........2 ....................................U 2....................... JAPANESE / .......... ............................. ................... ......................... ................... Power Supply Use only a Symbol approved power supply 50-14000-101R output rated 9 Vdc and minimum 1 A. The power supply is certified to EN60950-1 with SELV outputs. Use of an alternative power supply invalidates any approval given to th

No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Symbol products. Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks

All rights reserved. © 2006 by Symbol Technologies, Inc. All rights reserved. The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Symbol grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consen

See Product Reference Guide for more information Miscellaneous Settings LS2208 LS2208 Quick Start Guide POST IN WORK AREA IntelliStand Accessories 3 LS2208 72-71882-01 Rev A April 2005 Laser Labels In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user: ENGLISH HEBREW CLASS 1 CLASS 1 LASER PRODUCT CLASS 2 LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT DANISH / DANSK ITALIAN / ITALIANO KLASSE 1 KLASSE 1 LASERPRODUKT CLASSE 1 PRODOTTO AL LASER

Es muss gewahrleistet sein, dass die Scanzeile alle Balken und Zwischenraume des Symbols uberstreicht. RICHTIG FALSCH 012345 012345 4. Nach erfolgreichem Decodieren gibt der Scanner einen Piepton ab, und die grune LED wird aktiviert. 10 Kurzubersicht Kurzubersicht Im Tischstander bleibt der Scanner konstant eingeschaltet. Wenn Sie den Scanner aus dem Stander nehmen, schaltet er in den normalen Handbetrieb um (das hei.t, je nach Modell ist er dann konstant eingeschaltet oder er befindet sich im A

All rights reserved. © 1997 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, s

All rights reserved. CopyrightO 1996 by Symbol Technologies, Inc. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any co

T350 (1) Loosen the 2 joint bolts fully. JOINT BOLT JOINT GROUND WIRE THROTTLE GRIP (2) Slip the outer tube into the joint until the tube bottoms. The outer tube or gearcase shaft may have to be rotated slightly for the splines on the mainshaft to fully engage to the engine. Assembly of the Outer Tube C350/B450 (1) Loosen the 2 joint bolts fully and slip the outer tube into the joint until the tube bottoms (up to the insert label). The outer tube or gearcase shaft may have to be rotated slightly

This machine is designed for cutting grass, weed, and bushes. Do not use this machine for other purposes. Minimize the risk of injury to yourself and others. Do not operate or service this machine unless you clearly understand this manual. Keep this manual at a particular place so that you can reread it whenever you have a question about its use. Part Number 62102-94310 Rev. 02/05 Introduction Attention Statements IMPORTANT! The operational procedures described in this manual are intended to hel