DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO ILLUMINATION INPUTS AS DAMAGE TO LIGHTS WILL OCCUR. 10. Illumination connection: The positive (+) output from your 12V system connects to the positive (+) input, and the negative (ground) connects to the negative (-) input on the input cup located on the rear of the subwoofer enclosure. Improper 12V polarity will not cause damage to the lights, but they will not illuminate. XOBP12D GUIDELINES Enclosure Guidelines To achieve the best possible sound from t

If you feel unsure about installing this system yourself, have it installed by a qualified audio technician. Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. Do not connect Amplifier or any audio source to illumination inputs. Inputs are designed for 12 volt power source only. SX SERIES INSTALLATION Installation The following installation instructions are very basic. If you feel unsure about personally installing this s

7. Avoid running wires over, near, or through sharp edged surfaces. We suggest you also use rubber grommets to protect any wires routed through metal, especially the firewall. SX SERIES INSTALLATION Mounting 1. Determine where the speakers will be mounted. Make sure the area is large enough for the speaker to mount evenly. Also ensure the mounting location is deep enough for the speaker to fit. 2. Refer to the specification chart to determine the proper diameter hole to cut for your speaker mode

If you feel confident in your ability to install this product without the assistance of a professional, please read this section thoroughly. We have provided a number of placement recommendations and installation tips to assist you. Keep in mind these are provided as a guideline and you may find that other placements specific to your vehicle may provide better results. • Make sure all moving parts and factory electrical wires are out of the way and will not interfere after installation. • Ensure

Noise and Hum -90 dB below full output ................................................................................................................................................ Input Impedance 50,000 Ohms - RCA 100,000 Ohms - XLR ................................................................................................................................................ Output Impedance 400 Ohms ............................................................................................

Balances the loudness of the Subwoofer relative to the Front speakers and compensates for room effects on the Subwoofer’s output. It should not be necessary to set the level control to maximum volume to achieve a well balanced installation, but you may need to adjust when changing between music CD's and DVDs. Important: Use Option1 or Option 2, but not both. OPTION 1. Connection with speaker wire -Connect speaker wires from the Receiver’s front left and right speaker outputs to the Subwoofer’s S

Dual audio products are constructed using the finest quality components and we are proud of our custom designed drivers and electronics. Much effort has gone into the design of your new sub as to help you achieve years of maximum performance and pleasure. Every DUAL loudspeaker undergoes rigorous testing and quality controls at the factory to ensure years of listening pleasure. Please take a moment to read this manual prior to installing your new subwoofer. The information provided will help you

Intercom Volume 4. FRS Radio Input 5. Intercom VOX Sensitivity 6. Cell Phone Input 7. FRS or CB Transmit Select Switch Motorcycle Connections / Controls 8. Rider Transmit (PTT) Push-To-Talk Button for FRS or CB radio 9. Connection for Rider Headset Cord 10. Passenger Transmit (PTT) Push-To-Talk Button for FRS or CB radio 11. Connection for Passenger Headset Cord 6 Rider / Passenger Intercom Operation The ComSystem intercom is a voice activated system that allows seamless communication between ri

No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages. Dual Electronics Corporation 21318 64th Avenue South Kent, WA 98032 U.S.A ©2005 Dual Electronics Corp. EVOK0404-V01

Drill the holes with a 1/8" bit. 4. Be sure to observe proper polarity when connecting the wires. The speaker's positive terminal is indicated with the “+” symbol. 5. Fit the ring and speaker to the cut-out. Mount them using the enclosed screws. If supplied, fit the grille inside the ring and press gently, but firmly, into place and attach with screws. 5 XNP - SBX SERIES INSTALLATION Mounting Legend 6 XNP - SBX SERIES SPECIFICATIONS Notes 7 XNP - SBX SERIES WARRANTY Limited One-Year Warranty Thi