. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 1080sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Introduction .. .. .. .. .. .. .. .. .. .. .. .. . 1

The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data. The following conditions are considered DST failure conditions: • Seek error after retries are exhausted • Track-follow error after retries are exhausted • Read error after retrie

Bits 7, 6, 5, 3, 2, 1, and 0 are changeable, because those bits are all ones. Bit 4 is not changeable. Though the drive always reports non-zero values in bytes 00 and 01, those particular bytes are never changeable. The Changeable values list can only be changed by downloading new firmware into the flash EPROM. On standard OEM drives the Saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping. When a drive is powered up

Cheetah 10K.7 SCSI Product Manual, Rev. D Table 15: LW 68-conductor LVD P cable signal/pin assignments [11] Note. Note: A minus sign preceding a signal name indicates that signal is active low. Signal name [1] Connector contact number [3] Cable conductor number [2] Connector contact number [3] Signal name [1] +DB12 1 1 2 35 –DB12 +DB13 2 3 4 36 –DB13 +DB14 3 5 6 37 –DB14 +DB15 4 7 8 38 –DB15 +DBP1 9 39 –DBP1 +DB0 6 11 12 40 –DB0 +DB1 7 13 14 41 –DB1 +DB2 8 15 16 42 –DB2 +DB3 9 17 18 43 –DB3 +DB4

• Befolgen Sie die oben unter “Electrostatic Discharge Protection” angegebenen Sicherheitsma.nahmen. • Nehmen Sie keine Platinen aus dem Laufwerk. Wenn eine Platine defekt ist, mu. das gesamte Laufwerk zur Reparatur eingeschickt werden. Die Herausnahme von Platinen durch andere Personen als die fur die werkseitige Reparatur zustandigen kann zu einer Beschadigung der Komponenten und Erloschen des Garantieanspruchs fuhren. Cheetah 18 Installation Guide, Rev. A • Die vormontierte Kopf- und Festplat

Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.). Sicherheitsanleitung 1. Das Gerrat ist ein Einbaugerat, das fur eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benotigt. Bei seitlicher Befestigung darf die maximale Lange der Schrauben im

To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at for more information. Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only fac

If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and

Do not drop or jar the drive. Handle the drive only by the edges or frame. • Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground. • Turn off the power to the host system during installation. • Do not disassemble the drive; doing so voids the warranty. Return the entire drive for depot service if any part is defective. • Do not apply pressure or attach labels to the drive. Setting the jumpers Refer to the ju

2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the autodetect option and enable it. If your drive has a problem, it may not be recognized by the system. 3. Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system. 4. Does Scandisk find the drive defect-free? Scandisk is a utility located on you