16 WARRANTY WARRANTY LIMITATIONS WARRANTY TERMS The following is NOT covered under TUNN (Effective April 1st. 2008) warranty program: These terms supersede all prior published warranty terms 1. Product owned by anyone other than the TUNN products are warrantied against original purchaser from an authorized TUNN dealer. defects in materials and workmanship for (The warranty is NOT transferable and a period of One (1) Year from the original will not apply to products purchased from date of purchas

The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250

• NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at the amplifier may cause damage to the amplifier and will void your warranty. • Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to dete

Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. Features • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' Technology MOSFET PWM Power Supply. • Bridgeable & TRI-Mode Operation. • Continuously Variable 12dB/Octave High Pass & 12dB /Octave Low Pass Crossover. • Subwoofer Variable Crossover for Deep Bass Control. • Enhanced Bass Boost +12dB @ 45Hz. • Silver Plated

Use Solder or a clamp ring to connect the ground wire. Pre-drill the prepped chassis to bolt the ground ring terminal with nut, bolt and lock washers. Insulate metal and connector with paint or silicon to prevent rust and oxidation. Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile. Upon completion of the ground connection, grab wire or connector and confirm that it is a solid connection. To prevent engine noise, it is recommended to gr

Check all grounds , battery voltage, and RCA cables Ticking noise on audio with engine running Amplifier is picking up radiated spark noise Check RCA audio cable; Install an in-line noise filter on the head unit's power wire. Check spark plug wires. 14 SPECIFICATI SPECIFICATISPECIFICATION ONON Output Power Rating RMS T-270 T-2100 T-2130 Channel 2CH 2CH 2CH Total Max Power 900 Watts 1200 Watts 1500 Watts 4 Ohm at 14.4V 0.3%THD ( RMS ) 4 Ohm at 14.4V ( MAX ) 2 Ohm at 14.4V 0.3%THD ( RMS ) 2 Ohm at

Because the Class "D" amplifier is capable of drawing in excess of 90 amperes,4 gauge wire is recommended for lengths up to twenty feet. if a longer length is needed , a larger gauge wire may be necessary. POWER Amplifier power wire should be wired directly to the battery using the wire requirements listed above. Start at the amplifier and run the power wire through the vehicle to the battery. The use of grommets is recommended when passing the power wire through any metal wall. Avoid sharp corn

Master Amplifier Slave Amplifier Recommend : Competition Only MONO BRIDGED SPEAKER WIRING FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION 6 Master Amplifier

It will explain the features and operation of your unit and help insure trouble free installation. FEATURES • Class ''D'' Technology • 1 Ohm Stable • Spec Audiophile Grade Components • High Efficiency PWM Power Supply - Multi-stranded power toroid - Tow toroidal core - MOSFET transistors • Oversized Capacitor Banks • Discrete Mount Power and speaker terminals • Variable Low Pass Electronic Crossover 50Hz -250Hz • Built in power bridging module • Circuit / Thermal / Overload Protection • Bridge S

16 WARRANTY applied to products. (Interfire Audio will not be WARRANTY LIMITATIONS The following is NOT covered under Interfire Audio's warranty program: manual lightning, etc.) Custom finishes) Product with defaced, altered or removed serial numbers (no valid, legible serial No. = no warranty). or missing magnets. 1. 3. 4. 5. 6. 7. 8. WARRANTY TERMS (Effective January 01, 2010) These terms supersede all prior published warranty terms Interfire Audio products are warrantied against defects in ma