Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
No. Part No. Description 1 505372 Inlet Bushing with Screen 2 505709 Deflector 3 505371 O-RIng 4 505710 Valve Spring 5 505367 Valve 6 505366 Valve Pin 7 505365 Valve Seat 8 505713 Roll Pin 9 505867 Motor Housing 10 505868 Roll Pin 11 505869 Roll Pin 12 505870 Reverse Lever 13 505871 Spring 14 67202 Steel Ball 15 505711 Muflier 16 505714 Valve Shaft 17 505715 Trigger 18 67081 O-Ring 19 505872 Reverse Valve 20 505873 Ball Bearing Ref. No. Part No. Description 21 66570 Roll Pin 22 505874 Rear Plate 23 66502 Roll Pin 24 505875 Cylinder 25 66507 Rotor Blade {Set of 4) 26 505768 Rotor 27 505876 Front Plate 28 66504 Ball Bearing 29 505722 Spacer 30 505877 Internal Gear 31 505878 Idler Gear (3)* 32 505879 Spindle including Pin x 3 33 67328 Ball Bearing (2)* 34 505736 Clamp Nut 35 67421 Chuck Screw 36 505880 Name Plate 37 67255 Name Plate Screw (2)* Not Shown 505001 Warning Label Nol Shown 505881 3/8" Keyless Chuck Page No 3 5203 3/8" Reversible Micro Drill Ref. No. Past №. Description 1 505372 Inlet Bushing with Screen 2 505709 Deflector 3 505371 O-RIng 4 505710 Valve Spring 5 505367 Valve 6 505366 Valve Pin 7 505365 Valve Seat 8 505713 Roil Pin 9 505867 Motor Housing 10 505868 Roll Pin 11 505869 Roll Pin 12 505870 Reverse Lever 13 505071 Spring 14 67202 Steel Ball 15 505711 Muffler 16 505714 Valve Shaft 17 505715 Trigger 18 67081 O-Ring 19 505872 Reverse Valve 20 505873 Ball Bearing Ref. No. Part No. Description 21 66570 Roll Pin 22 505874 Rear Plate 23 66502 Roll Pin 24 505875 Cylinder 25 66507 Rotor Blade {Set of 4) 26 505768 Rotor 27 505876 Front Plats 28 66504 Ball Bearing 29 505722 Spacer 30 505877 Internal Gear 31 505878 Idler Gear (3)* 32 505879 Spindle including Pin x 3 33 67328 Ball Bearing (2)* 34 505736 Clamp Nut 35 67421 Chuck Screw 36 505880 Name Plate 37 67255 Name Plate Screw (2)* Not Shown 505001 Warning Label Nol Shown 505881 3/8' Keyless Chuck 'Order Quantity Needed Page No 3 Reassembly Clean al! parts and examine for wear before reassembling. Look In particular for wear and cuts on O-rings, wear on rotor blades, gear and clutch components. Lightly coat all parts with a suitable pneumatic tool lubricating oil, preferably one incorporating a rust Inhibitor and grease all bearings, gears, and clutch parts with a molybdenum or lithium based general purpose grease. Before reassembling the motor, make sure that the faces of end plates {22, 27) that abut cylinder (24) are flat and free from burrs and sharp edges. If necessary, lap on a flat very fine grade of abrasive paper. Reassemble in the reverse order. When refitting the complete motor assembly to the housing (9) f I rst, make sure that the assembly is clamped tightly together and the rotor spins freely. When assembling clamp nut (34) to motor housing (9), tighten clamp nut to between 3.0 kg/m and 4.0 kg/m by using a Torque wrench. Operation Specification Air Consumption 2.5 cfm {18 scfm) Air Inlet Thread 1/4-18NPT Overall Length 6.6“ (168 mm) Minimum Hose Length 8 feet of 5/16" (8mm) Dia. at 90 PSIG/6.2 bar NOTES Manufacturer/Supplier Sioux Tools Inc. 2901 Floyd Boulevard P.O. Box 507 Sioux City, IA 51102 U.S.A. Tel No. 712-252-0525 Fax No. 712-252-4267 Product Type 3/8" Reversible Micro Drill RPM 1,550 Cycles Per Min. C€ Model No/Nos 5203 Serial No. Product Net Weight 2.25 lbs 1,02 Kg Recommended Use Of Balancer Or Support N0 Recommended Hose Bore Size - Minimum 5/16 Ins 8 M/M Recommended Max. Hose Length 30 Ft 10 M Air Pressure Recommended Working 6.2 bar 90 PSI Maximum 6.2 bar 90 PSI Noise Level: Sound Pressure Level 82.0 dB(A) Test Method: Tested in accordance with Pneurop test code PN8NTC1 and ISO Standard 3744 SAFETY MESSAGES Personal Safety Equipment Use - Safety Glasses YES Use - Safety Gloves Use - Safety Boots Use - Breathing Masks Use - Ear Protectors YES A WARNING /■^k Always Read Instructions >Ak Before Using Power Tools ¿S&t Always Wear Safety Goggles Wear Hearing Protection /\ Avoid Prolonged Exposure /™ To Vibration Vibration Level Less Than 2.5 Meters/Sec2 Test Method: Tested in accordance with ISO standards 8662 Part 1 & 7 /’*£ Declaration of Conformity Sioux Tools Inc. 2901 Floyd Boulevard, P.O. Box 507, Sioux City, Iowa 51102 declare under our sole responsibility that the product Mode! 5203 Micro Drill, Serial Number to which this declaration relates is in conformity with the following standard(s) or other normative document(s) EN792 (Draft), EN292 Parts 1 & 2, ISO 8662 Part 1 & 7, Pneurop PN8NTC1 following the provisions of 89/392/EEC as amended by 91/368/EEC & 93/44/EEC Directives Gerald E. Seebeck (President) ^_________________Naroe^nd signature o^qulvalent marking of authorized person...