Login:
Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Anleitung Seagate, modell BARRACUDA 7200.7 ST3200822A

Hersteller: Seagate
Dateigröße: 116.08 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Do not drop or jar the drive. Handle the drive only by the edges or frame. • Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground. • Turn off the power to the host system during installation. • Do not disassemble the drive; doing so voids the warranty. Return the entire drive for depot service if any part is defective. • Do not apply pressure or attach labels to the drive. Setting the jumpers Refer to the jumper settings illustration below or on your drive label to configure the drive for your system. Jumper settings can also be accessed online from our web site at • Master or single drive: The drive is shipped configured for a master or a single drive with a jumper set on pins 7 and 8. • Drive is slave: To configure the drive as a slave or second drive on the cable, remove all the jumpers. • Master with non-ATA compatible slave: Use this setting if the slave drive is not recognized. Configure the master drive with a jumper set on pins 5 and 6 and pins 7 and 8 to enable this option. • Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interOptions jumper block face bus. To enable cable select, set a jumper on pins 5 and 6. • Alternate capacity jumper: Drives with a 40-Gbyte capacity or greater are limited to 32 Gbytes. Use this jumper only if you have a legacy system with a BIOS that does not support large capacity disc drives. When using the alternate capacity jumper, • Manager software is required to achieve the drive’s full capacity. 268 4 1753 Drive is slave *Master or single drive *Cable select Master with non ATA- compatible slave Alternate capacity. Limits drive capacity to 32 Gbytes Attaching cables and mounting the drive 1. Attach one end of the drive interface cable to the interface connector on your computer’s motherboard (see your computer manual for connector locations). Master Pin 1 Slave Note. When configuring two ATA devices on the same cable, both must use Cable Select or both must use Master/Slave jumper settings. If using a standard 40-pin cable, the master and slave drives can be placed in any position. If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and no more than 0.14 inches (3.55 mm) into the side-mounting holes. Note. Do not overtighten the screws or use metric screws. This may damage the drive. 3. Attach the interface connector and the power connector to the drive. Configuring the BIOS Close y...

Dieses Handbuch ist für folgende Modelle:
Player - BARRACUDA 7200.7 ST3120022A (116.08 kb)
Player - BARRACUDA 7200.7 ST3120026A (116.08 kb)
Player - BARRACUDA 7200.7 ST3160021A (116.08 kb)
Player - BARRACUDA 7200.7 ST3160023A (116.08 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien