Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Danger of electrocution. Risk of scalding. APPLICABLE STANDARDS The products have received the “CE” certificate in accordance with the standards prevailing in different countries (European Directives 92/42/EEC, “efficiency”, 90/396/EEC “gas appliances”). These products have also received the Belgian “HR+” (gas boilers) marks. WARNINGS These instructions are an integral part of the equipment to which they refer and must be supplied to the user. The product must be installed and serviced by qualified engineers, in compliance with the prevailing standards. ACV accepts no liability for any damage resulting from incorrect installation or from the use of components or fittings not specified by ACV. Failure to observe instructions regarding tests and test procedures can result in personal injury or pollution risks. Note: ACV reserves the right to modify the technical specifications and components of its products without prior notice. DESCRIPTION OPERATING PRINCIPLE The HeatMaster is a high performance, direct fired hot water storage heater, which has indirect heat transfer due to its Tank-in-Tank construction. At the heart of the HeatMaster is a stainless steel cylinder through which the flue tubes pass. This is surrounded by a mild steel shell containing the primary water (neutral fluid). The outer shell extends down to the combustion chamber and even around the flue tubes. The area of the heat transfer surface is therefore much greater than that of standard direct fired water heaters. A circulating pump fitted to the primary circuit moves the water around the tank, heating it faster and maintaining an even temperature across the primary jacket. The burner, either gas or oil, fires onto the primary water which indirectly heats the stainless steel cylinder containing the DHW. As with all Tank-in-Tanks, this is corrugated over its full height and suspended in the HeatMaster by its hot and cold water connections. The cylinder expands and contracts during use and this, together with the fact that cold water does not come into contact with the intense heat of the burner flame, means that limescale buildup is prevented. This scale resistant feature, along with the corrosion resistance of stainless steel, eliminates the need for sacrifical anodes. The HeatMaster has one very major advantage over other direct fired water heaters - because it heats the DHW with a primary circuit, this primary water can be used to provide central heating as well. By connecting two, three, four or more HeatMasters together in a module, most hot water and heating demands can be met. Indeed, when used in conjunction with HR and Jumbo hot water storage tanks the Heatmaster can supply even the largest hot water requirement. Standard equipment The HeatMaster 71/101 has the following items as standard : - On/off switch - Summer/Winter switch - MCBA controller, incorporating • electronic control and high limit thermostats • burner modulation - primary circulating shunt pump - primary expansion vessels - primary safety valve - pressure and temperature gauge - drain valve - body completely insulated in rigid polyurethane foam CONSTRUCTION FEATURES Outer body The outer body containing the primary fluid is made of carbon steel (STW 22). TANK-IN-TANK heat exchanger The ring-shaped inner tank with its large heating surface for producing domestic hot water is built of Chrome/Nickel 18/10 stainless steel. It is corrugated over its full height by an exclusive production process and entirely argon arc welded by the TIG (Tungsten Inert Gas) method. Combustion gas circuit The combustion gas circuit is paint protected and comprises: • Flue pipes HeatMaster 71/101 models contain 8 steel flue pipes with an internal diameter of 64 mm. Each pipe is fitted with a turbulator of stainless steel designed to improve heat exchange and to reduce flue gas temperature. • Combustion chamber The combustion chamber on HeatMaster models is entirely water cooled. Insulation The boiler body is fully insulated by rigid polyurethane foam with a high thermal insulation coefficient, sprayed on without the use of CFCs. Casing The boiler is covered by a steel casing which has been scoured and phosphated before being stove enamelled at 220 °C. Burner 71 and 101 models are always delivered with ACV BG 2000-M 71 and 101 air/gas premix burners. DESCRIPTION Top cover Flue reduction collar Automatic air vent Central heating flow pipe Flue pipes and turbulators Insulation Burner Heating return Combustion chamber Burner chamber plate Primary circuit Casing front panel Primary expansion vessel Domestic cold water inlet Heating circuit filling valve with removable hose and non-return valve Primary shunt pump Domestic hot water outlet Tank-in-Tank heat exchanger Detector NTC1 and NTC2 Detector NTC3 Low water pressure switch Primary safety valve TECHNICAL SPECIFICATION DIMENSIONS The units are delivered fully assembled, tested and packed on a timber base with shockproof edges and protected by hea...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - HM 71 (586.54 kb)