Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Factory Recommends Professional Installation ALL UNITS TESTED AND Manufactured by National Steelcrafters of Oregon Inc. _ ^ ^ __ . __ ÔfMTfONAL STEELCRAFTERS OF $ P.O. Box 24910 oneûûNiNc icBOTL-116 NER-QA-219 Eugene, Oregon 97402 3S7 1000 PAGE 1 Thank you for purchasing the Breckwell Pellet Burning Stove. You are now prepared to burn wood in the most efficient, convenient way possible. To achieve the safest, most efficient and most enjoyable performance from your stove, you must do three things: 1) Install ft properly; 2) Operate it correctly CONTENTS and; 3) Maintain it regularly. The purpose of this manual is to help you do all three. PLEASE read this manual thoroughly before beginning your installation and KEEP IT in a handy place for future reference and for future owners. 1.0 Introduction 2.0 Installation 2.1 Preparation 2.2 Clearances 2.3 Combustion Air Supply 2.31 When Outside Air is Not Used 2.4 Venting 2.41 P24FSA and P24FSL 2.42 P24I 2.5 Electrical Installation 2.6 Special Mobile Home Requirements 3.0 Operation 3.1 Proper Fuel 3.2 Pre-Startup Check 3.3 Building a Fire 3.31 Using Approved Fire Starter 3.32 Optional Hot Rod™ 3.4 Panel Controls 3.5 Optional Thermostat 3.6 Damper Control 3.7 Refueling 3.8 Breckwell Tool 3.9 Shut Down Procedure 3.91 Safety Features 3.921 Operating Safety Precautions 4.0 Maintenance 4.1 Ash Disposal P24I 4.11 Ash Disposal P24FSA and P24FSL 4.12 Vacuum Use 4.2 Cleaning 4.3 Blowers 4.4 Chimney Cleaning 4.5 Recommended Maintenance Schedule 5.0 Trouble Shooting Guide 5.1 Fuel Will Not Feed 5.2 Fire Goes Out 5.3 Smoky Fire 5.4 No Power 5.5 Blowers Will Not Operate Properly 5.6 Noisy Operation 6.0 Replacement Parts List 1.0 INTRODUCTION Note which model you have purchased (either P24FSA, P24FSL freestanding models or P24I built-in fireplace or fireplace insert). Some instructions refer to only one model or the other. This stove has been independently tested and approved in accordance with the relevant portions of ULC S627 CSA B366.2-M1983 “Standard for Space Heaters for use with Solid Fuels”, UL 1482-1988 "Standard for Room Heaters", ASTM E1509-93, CSA C22.2 No. 3 “Electrical Features of Solid Fuel Burning Appliances”, Oregon new rules for mobile homes (814-23-900 through 814-23-909) and installation as a stove heater. This appliance is designed specifically for use only with pelletized wood. It is designed for residential installation according to current national and local building codes as a free standing room heater. It is also approved as a mobile home heater which is designed for connection to an outside combustion air source. The stove will not operate using natural draft, or without a power source for the blower systems and fuel feeding systems and must not be burned with any type of coal (see section 3.1). This stove is designed to provide the optimum proportions of fuel and air to the fire in order to burn free of smoke and soot. Any blockage of the air supply to or from the stove will seriously degrade the performance and will be evidenced by a smoking exhaust and a sooting window. For the best operation the ash content of the pellet fuel should be less than 1 % and the calorific value approximately 8200 BTU/LB. Avoid high ash content fuels as this will rapidly fill up the bum pot and eventually cut off the combustion air supply. Commercial and industrial installations of Breckwell Pellet Stoves should not be used since operational control is often not well managed in these settings. 2.0 INSTALLATION 2.1 PREPARATION Factory packaging must be removed and some minor assembly work is required prior to installation. Access to the rear of the stove is necessary. Foam protective blocks must be removed from all blowers and gear motor. This is a safety precaution. The circuit board/ control panel must be unplugged and installed in the P24I side panel. Instructions are packed with the board/panel. Free the power cord. NOTE: Normally, your dealer will perform these functions. 2.2 CLEARANCES The Breckwell P24FSA and P24FSL have been tested and listed for installation in residential, mobile home, and alcove applications. The P24I is approved for installation into masonry fireplaces; also factory built, built-in, zero clearance fireplaces of the following description: all brands at least 36" wide and 20" high. The P24I is also approved as a built-in fireplace, as long as minimum chase size and material specifications are maintained (see section 2.42D). FLOOR PROTECTION (P24FSA and P24FSL) minimum 25" wide by 35" deep. The stove must be placed on a continuous PAGE 2 (grouted joints) non-combustible material such as ceramic tile, cement board, brick, 3/8" asbestos millboard or equivalent, or other approved or listed material suited for floor p...
Dieses Handbuch ist für folgende Modelle:Kamine - P24FSA (462.74 kb)