DESCRIPTION Natural Propane Part No. Qty. Part No. Qty. 30. Gas Valve -SIT 43K0701 1 88J5301 1 31. Piezo Igniter 10K8601 1 10K8601 1 32. Pilot Assembly 69L1701 1 69L1801 1 33. Pilot Generator 60J7901 1 60J7901 1 34. Thermocouple 74L5701 1 74L5701 1 35. Pilot Tube 74L5601 1 74L5601 1 36. Electrode And Cable 74L5801 1 74L5801 1 37. Orifice 60J8001 2 19L5201 2 GAS CONTROLS — HONEYWELL ELECTRONIC No. DESCRIPTION Natural Propane Part No. Qty. Part No. Qty. 40. Gas Valve -Honeywell 62L1801 1 62L1901 1

116-F-13-4) to ANSI Z21.88-2002 (in Canada, CSA-2.33-2002), and CAN/CGA-2.17-M91 in both USA and Canada, as vented gas fireplace heaters. Both millivolt and electronic versions of these appliances are listed by Omni-Test Laboratories for installation in bedrooms and mobile homes. Installation must conform to local codes. In the absence of local codes, installation must comply with the current National Fuel Gas Code, ANSI Z223.1. (In Canada, the current CAN-1 B149 installation code.) Electrical w

Operating Instructions Operating Instructions Be sure to check these items before the initial lighting of the insert: c The insert gas label corresponds to the gas supply available -that is "natural gas" for natural gas or "LP gas" for LP gas. c Gas pressure has been checked carefully - see Page 13. c All gas fittings have been checked for leaks. c• All clearances to combustibles have been met-see Page 9. c All combustible materials have been removed from the area in front of the insert. c All v

IMPROPER INSTALLATION OR USE OF THIS APPLIANCE CAN CAUSE SERIOUS INJURY OR DEATH FROM FIRE, BURNS, EXPLOSION OR CARBON MONOXIDE POISONING. WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES. USE CAUTION AROUND THE APPLIANCE TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE. WARNING: DO NOT PLACE CLOTHING OR OTHER FLAMMABLE MATERIALS ON OR NEAR THIS APPLIANCE. AVERTISSEMENT: SU

Replace grills by aligning top ends of rods to upper set of holes on corresponding frames. Swing grilles towards frame in the same manner as they were removed and allow rod bottoms to fall into bottom holes until fully secured. Make sure all rods are completely inside holes. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. FireCraft Technologies reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and pr

AELBATVMMUMINImumixaMH teef )m( teef )m( 1 )503.0( 2 )16.0( 2 )16.0( 4 )222.1( 3 )419.0( 6 )68.1( 4 )22.1( 8 )4.2( .xaM)m4.21(teef04=H+V .xaM)m4.2(teef8=H BELBATVMMUMINIH mumixaMteef )sretem( teef )sretem( 1* )503.0( 5 )25.1( 2 )016.0( 01 )1.3( 3 )419.0( 51 )56.4( 4 )22.1( 02 )2.6( V+V 1 .xaM)m4.21(teef04=H+ H .xaM)m2.6(teef02= V H *CeilingFirestop/Spacer (SV4.5VF) **Wall Firestop/Spacer (SV4.5HF) A Vent Restrictor, as shown in Figure 20, page 10, must be used in this application *When using Sec

Severe burns may result. • Carefully supervise children in the same room as appliance. • If small children are present in the home, it is recommended that this appliance be fitted with a screen door or screen panel kit. See Page 15 for ordering information. WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY: Do not store or use gasoline or other flammables or liquids in the v

Refractory Liner Kit One of the most beautiful enhancements you can make to this appliance is the addition of refractory liners. The refractory liner kit includes tan ceramic fiber panels for the rear and side walls of the firebox. The ceramic fiber panels have brick-like features in relief. To install the three panels, simply place them in position against the firebox walls. This kit can be retrofitted into previously installed appliances. Screen Panel Kit An optional fixed fine mesh screen pan

Remove fireplace grille assemblies by lifting up and out of holes on frame. Then pull from bottom out towards you. (Figures 1 and 2). Note: Lift grille near outer support rods to fully clear holes. Step 2. Insert grille trim onto grille and bend tabs over and around until fully secured (See Figure 3 ). Bend tabs utilizing the flat end of a screw driver or pliers. Step 3. Remove protective covering from decorative grille trim pieces and wipe with damp cloth. Step 4. Replace grills by aligning

Turn off the gas supply to the appliance. discard the three pressure regulator mounting Remove the front glass door/frame from the screws. Remove the pressure regulator, spring, appliance. Access the control compartment. poppet, diaphragm and bushing. Discard all removed components. Ensure the rubber gas- Step 2. Carefully remove the logs. Exercise ket installed on the back of the replacement care as not to break the logs. pressure regulator is properly positioned and install the new pressure re