EFFECTIVELY HOLDS DOOR OPEN IN ANY POSITION. RUGGED CONSTRUCTION FEATURES RESILIENT NON-MARRING TIP. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips screwdriver, pencil and awl 1. Position door holder near edge of door, with top screw hole 4 Vs" above floor. (See illustration.) 2. Mark and secure. MAINTENANCE INSTRUCTIONS H.B. Ives Solid Brass products have a clear, protective lacquer coating which helps prevent discoloration Do not use abrasive waxes or cleaners. ASK FOR OTHER FINE DE

780 Door Chime DWG # 2375 Rev A, new drawing # 9/7/00 Tools Required: Hand or electric drill No. 2 point Phillips screwdriver 1 inch, 3/32 inch and 7/64 inch drills STEP 1 STEP 2 STEP 3 Mark horizontal reference line on OUTSIDE of door at convenient eye level (recommended 58 inches up from bottom of door). Mark vertical line on door centered from left to right. (See fig. 1) Align template reference lines with lines on door and mark location of 3 holes labeled "OUTSIDE ©" on door. Dril

Our commitment to quality makes IVES a name you can trust. HINGE PIN DOOR STOP FOR USE ON REMOVABLE PIN-HINGED TYPE DOORS TO STOP DOOR AND PREVENT DAMAGE TO DOOR, WALL AND DOOR KNOB. FEATURES REMOVABLE BUSHING TO ACCOMMODATE LARGE HINGE PINS. INSTALLATION INSTRUCTIONS L Using screwdriver aru igular sere1 id hammer, carefully remove pin (A) — HINGE PIN TOOLS REQUIRED: Regular screwdriver and hammer. Using from nings. 2. Position door stop on top of hinge and tap hinge pin (A) into hinge

Since 1876, UK fvesqualityhardwarebashelpedbund the most distinguished homes in America. DUTCH DOOR BOLT FOR USE ON DUTCH DOORS, OR STANDARD EXTERIOR AND INTERIOR DOORS. Provides added security with a decorative accent. INSTALLATION INSTRUCTIONS TOOLS REQUIRED; Drill, 7/64" drill bit fcr pilot holes, small chisel, Phillips screwdriver and pendL FOR DUTCH DOOR APPLICATION - 1. Position bolt approximately 2" - 3* from edge of door. Using dimensions in illustration (A) marie, drUl and secu

Our commitment to quality makes IVES a name you can trust. LEFT HANDED CASEMENT OPERATOR FOR USE ON STANDARD WOOD CASEMENT WINDOWS 14" TO 20’ WIDE AS REPLACEMENT FOR OPERATOR. FEATURES EASY INSTALLATION, SMOOTH OPERATION AND RUGGED CONSTRUCTION. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips screwdriver, owl or pencil. 1. Detach present operator base (A) from sill and pull metal extending rod (B) out of window track (C). 2. Position new operator in same location, connect metal ext

.. .... Ingersoll Rand © 2006 Ingersoll-Rand Company Limited Security Technologies 829168-00 INSTALLATION Q Mark frame hole locations. A. Open hinge and place frame leaf flat against surface of frame leaving 1/8” gap between top of hinge and frame header. Hinge lip should be held tight against the frame face from top to bottom. B. Mark all hole locations on frame using center punch provided. C. Drill all holes using #13 (.185”) or 3/16” (.188”) drill for metal frame. For wood frame us

Phillips screwdriver, chisel, hammer, awl, pencil, 1-1/4" spade bit or 1-1/4" router. New Installation: 1. Position top of hinge approximately 5" from top of door and bottom hinge approximately 10" from floor. Position the third hinge equally between the top and bottom hinges. 2. The hinge barrels should extend out l'romdoorenoughtocleardoorcasing. See illustration. 3. Trace hinge outline and mortise door to tit thickness of hinge leaf. The inside edge of hinge should be approximately 1/4" f

Secure with two screws provided. 3. Replace and secure front plate over sleeve. For New Mail Slot Installations: 1. Follow mail slot installation instructions. 2. Insert sleeve through door cutout and secure. 3. Secure front plate over sleeve. © 1993 H.B. IVES, Wallingford, CT 06492