However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator’s manual carefully and become completely familiar with the controls. The information contained in this manual applies to all Dixon® ZTR® Model 2700 Commercial Mowers. Your Dixon dealer will gladly answer any questions. See your dealer for warranty service, parts and repairs. INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . .

2. Attach bagger mount plate to rear of engine guard. Use four 5-16-18 x 3/4" carriage bolts and four 5/16-18" nyloc nuts. Refer to illustration. 3. Attach a bagger strap to side hole in bagger mount plate. Use 3/8-16 x 1" carriage bolt, 3/8" washer and 3/8-16" nyloc nut. Attach other end of bagger brace to top front hole in engine guard, using existing frame hardware. Refer to Figure 1. Repeat for other side of machine. MOUNT PLATE STRAP STRAP 8050-161 1. To prevent damage to grass bags, remove

Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a resu

Install the front and rear mount brackets to the deck with the pin and hairpin cotter supplied with the kit. 1. Make sure the tension release lever is forward or disengaged. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release lever to the rear and engage in the latch. 10 ASSEMBLY BELT COVER TAB 4 INSTALLING BELT COVERS RETAINER KNOB OUTER PULLEY COVER DECK BELT SHIELD MIDDLE CHUTE LATCH DECK BELT SHIELD WING NUT TAP SCREW BELT SHIE

Replace all worn or damaged decals. SAFETY INFORMATION 7 STRAP LANYARD SUPPORT BRACKET ASSEMBLY Collection System Tools Required Ratchet Torque Wrench ." Wrench ." Socket 9/16" Wrench 9/16" Socket 5/8" Socket 1. Open the mounting kit box and remove all of the components. 2. Place the support bracket on the frame and secure with (2) 539 990563, 3/8 x 1 bolts and (2) 539 976979, 3/8 nyloc nuts. 3. Place the hitch brackets on the frame and secure with (3) 990622, . x 1. bolts and (3) 539 101331, .

3. Screw middle parts of upright 2 firmly to lower part of upright 1 with 2 wing nuts 3. 4. Screw upper part of upright 4 to middle parts of upright 2 with 2 wing nuts 3. 1b zS Mowing correctly: To produce a well-maintained lawn we recommend cutting the lawn regularly one a week if possible. The lawn becomes thicker if cut frequently. Relatively long cut grass (> 1 cm) must be removed so that the lawn does not become yellow and matted. After relatively long intervals between mowing (holiday lawn

English CONTENTS Contents ..................................................................3 Introduction..............................................................5 Congratulations .....................................................5 General ..................................................................5 Driving and Transport on Public Roads .................5 Towing ...................................................................5 Operating ........................................

Hinweis: Der Motormaher kann im Accu-Betrieb oder als Handrasenmaher ohne Accu-Antrieb angewendet werden. Vorsicht! Die umlaufende Messerwalze kann zu Verletzungen fuhren. Der durch die Fuhrungsholme gegebene Sicherheitsabstand zwischen Messerwalze und Benutzer ist stets einzuhalten. Beim Arbeiten an Hangen immer quer zum Hang arbeiten und auf sicheren und festen Stand achten. Uben Sie besondere Vorsicht beim Ruckwartsgehen und D A A Die vom Hersteller am Gerat installierten Sicherheitseinrichtu

This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance. This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the safety of the operator and others. It

Set the desired engine speed with the throttle. Allow the engine to run at a moderate speed, “half throttle” for 3-5 minutes before loading it to heavily. USE FULL THROTTLE WHEN MOWING (no choke). Use full throttle when mowing 8050-031-a WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See Battery in the Ma