• Operation • Repair Parts FailureToDo SoCanResuit in Serious Injury. sears,RoebuckandCo., HoffmanEstates,IL 60179 U,S.A. For one year from the date of purchase, when this Craf_man Gas-Powered Brushwaeker is maintained, lubricated, and tuned up accordingto the operating and maintenance instructions in the operator's manual, Sears will repair, free of charge, any defect in materials or workmanship. • • This warranty excludes the blade, nylon line, spark plug, and air filter, which are expendable

9 • Start engine, tip tines off ground by pressing handles down and engage tine control to start tine rotation. Allow tines to rotate for five minutes. • Check tine operation and adjust if necessary. See "FINE OPERATION CHECK" in the Service and Adjustments section of this manual. TILLING HINTS _CAUTION: Until you are accustomed to handling yourtilier, start actual field use with throttle in slow position (mid-way be tween "FAST" and "iDLE"). To help tiller move forward, lift up the handles slig

13. Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run. 14. Disengage power to the auger/impeller when transporting or not in use. 15. Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when backing up. 16. If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thorou

21 HOW TO REMOVE THE SNOW HOOD To access the spark plug, the snow hood must be removed as follows: 1. Remove the choke control knob (see Figure 21). 2. Remove the safety key. 3. Remove the mounting screws (see Figure 22). 4. Slowly remove the snow hood. Make sure that the primer button hose and the Ignition wire are not disconnected. 5. The spark plug can now be accessed. 6. To install the snow hood, first make sure that the primer button hose and the ignition wire are connected. 7. Mount the sn

Tth. 57 734-04155 Deck Wheel, 5" Dia. Ball 29 736-0262 Flat Washer, .385 x .870 x .092 58 938-3056 Shoulder Bolt, 3/8-16 43 Craftsman Engine IViodel 331777=1372=B2 For IViodel 247.28904 1330 REPAIR MANUAL 46S.ORTOPERATOR'SI [1329ENGINEI BLOCK ] I 1056MANUALREPLAOEMENT _.._ 85o 584 .........__.__ 1264 684 _-_ _" 1263 _ j" 306 i 307 _L_ _'_: ,,_&,..-% 26 718 d_-_%_ 616 _ 4O4 759 614 46 43 24 . 8471 842 '1/ x. 1o27 750 6 524 d_') 22_ 200 15 44 Craftsman Engine IViodel 331777=1372=B2 For IViodel 247

Password can be easily changed if desired. Temporary password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries. Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes. Operation: Opener activates when 4-digit password and Enter button is pressed. If wrong

731-06836 Cover,RearFenderRH 41. 783-04711B-0637 Arm,DeckLift LH 18. 731-06835 Cover,RearFenderLH 42. 783-05816-0637 Bracket,Seat Pivot 19. 731-06208 Spacer,SeatAdjust 43. 783-05817-0637 Plate,SeatMounting 20. 732-04459 Spring,Lift HandleTorsion 44. 783-05865A-0637 Fender,Rear 21. 732-04491 Spring,SeatAdjust 45. 925-04040 Switch,Seat 22. 732-04508 Spring,Compress.,1.71x 3.25x .23 46. 725-04658 Harness,Seat SwitchJumper 23. 732-0826A Spring,Extension,.865x 4.68 47. 757-04040 Arm Rest,Seat 24. 735

,, SAFETY * ASSEMBLY * OPERATION * MAINTENANCE * PARTS LIST . ES PAI'i,IO L Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our web site: FORM1/O.769-05040 5/4/2009 WarrantyStatement Pace2 .................................. SafeOperationPracticesPaces3-6 .......................... SafetyLabels............................................e7 Pac Assembly.................................................. Paces8-11 Operation..................................................es12-13 Pac

In-Lever sert universal joint pin (ensure ure 7 opening in pin is in line with NOTE: If the cables have become dis- small openings in universal connected, reinstall springs as shown in joint). Figure 8. 10. Place yoke end of crank rod around universal joint, lining up openings. Insert clevis pin through Auger Drive assembly and secure with cotter Traction Drive Spring (Short) pin. Spread ends of cotter pin to Spring (Long) lock in place. 11. Tighten aut on eye bolt. Make sure eye bolt is properl

358.794772 • Safety • Assembly • Operation • Maintenance • Parts List • Espa_ol, p, 20 WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun. 1-800-235-5878 _.oors,,s,edaroT,,'_ ceo,,o, Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 545167641 Rev. 4 4/16/08 BRW Warranty Statement 2 Storage 13 Identification of Safety Symbols 2 Troubleshooting