. Pressing the STOP button stops the alarm and rotor, and all outputs are off. 3-8. PREHEAT CONTROL To abort a Cook or Hold Cycle, press and hold the STOP button for 2 seconds. The Cook Cycle can also be paused by pressing and releasing the STOP button. If power is removed at any time, the control will resume the operation that was active at power down, whether it was in a Cook Cycle, Hold Cycle, or preheat. During preheat, the air heat and radiant heat are both turned on to regulate the air tem

all parameters must be reset using IR adapter tool P/N 98990001. Please refer to service manual for detailed instructions. 8 60136501 Coil Carrier Nut 3 9 98102901 Coil Carrier Fajita 1 10 72140130 Upper Case "SH/BA" 1 11 77322001 Ceran Glass 320x320mm 1 12 4522396 Induction Overlay 1 13 35624001 Front Indicator Lamp 24V LED Green 1 14 94900070 Control Switch 1 15 39400004 Plastic Knob 1 16 64070017 Bolt (M4x12) 4 17 60056701 Plain Large Washer 4 18 60099401 Pen Head Tapping S

cycle temperature. INSTRUCTIONS PRESS DISPLAY To adjust the oven temperature higher: 1. Press _ for 6 seconds (Fig. 1). 2. To increase the temperature use the number pads to enter the Figure 1 desired change. (Example 30°F) _ _ (Fig. 2). The O temperature may be increased as much as 35°F (17°C). Figure 2 3. Press _ to accept the temperature change and the display will return to the time of day (Fig. 3). Press _ to reject the change if necessary. Figure 3 To adjust the oven temperature lower: 1.

4. Replace the door mounting screws (See A in illustration). 5. If the door is not in line with the oven frame, remove it and repeat the above steps. 33 General Care & Cleaning FEATURE OVERVIEW Removing & Replacing Warmer Drawer To Remove and Replace Warmer (Warm & Ready TM) Drawer Pull up with finger To Remove Warmer Drawer: 1. r_ _ Turn power off before removing the warmer drawer. 2. Open the drawer to the fully opened position. 3. On the right glide you wilt find a shield attached with a hex-

Range Summit Full-Size Standard Depth, suffix S1 or Deep Depth, suffix D1 gas convection oven. 60,000 BTU (17.6 kW) cavity, 3/4 HP fan motor with two-speed fan speed control. Electronic spark ignition. Natural or propane gas. Summit 45 Solid State, Digital Controller 150°F-500°F (66°C-260°C) w/Pulse Fan & Cook 'n' Hold w/100 hour timer. Auto Cool Down / Auto Set Back feature. Porcelain enameled oven interior with coved corners, five (5) oven racks and 10-position rack guides. All model interiors

Range products are not approved or authorized for home or residential use, but are intended for commercial applications only. Garland / U.S. Range will not provide service, warranty, maintenance or support of any kind other than in commercial applications. 6" [152mm] 4" [102mm] SERIES HEIGHT WIDTH DEPTH GAS INLET RGTA 16 3/4" (425 mm) RGTA-2424-1 RGTA-2436-1 RGTA-2448-1 RGTA-2460-1 RGTA-2472-1 28" (711mm) 3/4" N PT 24" (610 mm) 36" (914mm) 48" (1219mm) 60" (1524mm) 72" (1829mm) R

However, only the selected surface Burner will lite. 4. Visually check that zone A & B of the dual burner has lit. 7. When both zones are lit, continue to turn the control knob counterclockwise between dual Hi & LO to adjust to the desired flame size for both burners together. Note: The markings between the Dual Hi and LO settings on the control knob adjust the flame size for both zone A & B (Refer to Figure 2 or 3). DO NOT cook with any of the surface control knobs in the LITE position (The ele

Inhalation of airborne particles of glass wool/ceramic fibers is known to the state of California to cause cancer. Part # 1009080 Rev 5 (01/25/08) Page TABLE OF CONTENTS IMPORTANT INFORMATION 2 DIMENSIONS 4 ELECTRICAL SPECIFICATIONS . 5 INTRODUCTION 6 Rating Plate. 6 INSTALLATION 7 Unpacking. 7 Leg Installation. 7 Electrical Connections. 7 E24-12H Hot Plate. 7 E24 Series Griddles. 7 INITIAL OPERATION . 8 Griddle Seasoning Instructions. 8 OPERATION 8 Open Type Burners. 8 E24 Series Griddles. 8 Ca

These are required if service technicians need to check a thermocouple without a J calibrated temperature meter. Check the thermocouple if you find the temperature variation of the thermostat is more than ± 5.F from the set point. To check a thermocouple, follow this procedure: Note: The Type J thermocouple requires the use of a Type J temperature meter. If a type J meter is not available use a millivolt meter and refer to the tables of degrees/millvolt values following, to calculate the cold ju

Exhaust fan ventilation hoods and grease filters should be kept clean. Do not allow grease to accumulate on hood or filter. Greasy deposits in the fan could catch fire. When flaming food under the hood, turn fan on. Refer to hood manufacturer's instructions for cleaning. * Use Proper Pan Size. This appliance is equipped with one or more cooking zones of different sizes. Select utensils having fiat bottoms large enough to cover the cooking zones. The pan detection sensors will not allow the affec