Montez le support mural (fourni avec la hotte). 2. Vissez la partie inferieure de la rallonge sur la hotte et vissez la partie superieure sur le support mural. 274.32cm (108po) minimum– 375.92cm (148po) maximum Sont fournis : 2 -Caches de conduit 1 -Paquet de vis de montage 89.8cm 89.8cm - 178.4cm CHMEX8036 Rallonge pour Cache de Conduit de Cheminee pour Hottes JXT8030, JXT8036, JXT8042 1. Montez le support mural (fourni avec la hotte). 2. Vissez la partie inferieure de la rallonge sur la hotte

When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is drawn out. OFF/ON OPERATION TEMP/TIMER COOL FAN HIGH MED LOW MODE FAN SPEED SET TIMER SET/ CANCEL AIR SWING EC ONOMY hr °F Wireless Remote Control 3 PART IDENTIFICATION 4 PREPARATION BEFORE OPERATING ACCESSORIES • Remote control • Two R03 dry-cell batteries Be sure to observe the following: • Aim remote control at control panel on air conditioner when operating. • Do not

Les penderies ne peuvent pas porter le poids de vetements lourds (comme les manteaux). 840168300 nv01.qxd 5/10/07 12:44 PM Page 4 840168300 nv01.qxd 5/10/07 12:44 PM Page 5 Garantie limitee Cette garantie s’applique aux produits Ce produit est garanti contre tout vice de materiau d’ouvre pendant une periode un (1) an a partir original, sauf indication suivante. Pendant cette periode, nous reparerons ou remplacerons GARANTIE REMPLACE TOUTE AUTRE GARANTIE OU CONDITION, EXPRESSE OU IMPLIQUEE, ECRIT

Depending upon the location of the unit, it may be necessary to change the side on which the dryer door opens. DC68-01052A

(Dimension “F” must be greater than 1/4" to prevent standing water in disposer.) If replacing an existing disposer, skip ahead to Instruction 6. Instruction 2. DISCONNECT SINK DRAIN 1. Loosen nut (A) at top of “P-trap” with pipe wrench (see Figure 2-1). 2. Loosen nut (B) at top of extension pipe. Remove extension pipe. 3. lubricant.) 4. 5. DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY 1. Insert wrenchette (or screwdriver) into one mounting lug and hold lower mounting ring securely with one hand (se

...............................................................................22 Accessories................................................................................22 In Canada ...................................................................................22 WARRANTY ..................................................................................23 SECURITE DE LA CUISINIERE ...................................................24 La bride antibasculement..............................

Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Plug into a grounded 3 prong outlet. WARNING Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can result in back or other injury. 2. Style 1 - For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See “Gra

It is important that you remove only the 6 indicated screws. 5. Lift the inner door assembly off of the outer door assembly. Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly aside. Reverse the hinge and hinge bracket 1. Place the inner door, screw head side up, on the work surface. 2. Remove the 4 screws that hold the hinge to the door. 3. Remove the 2 screws that hold the handle bracket to the door. 4. Move hinge to the other si

¦ Do not use an exhaust hood with a magnetic latch. Improper venting can cause moisture and lint to collect indoors, which may result in: Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc. Housecleaning problems and health problems. 11 Plan Vent System Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D A E F G H A. Dryer E. Clamps B. Elbow F. Rigid me

Typical Wiring Diagram for 208-230/1/60 with Fan Cycling. Models 049-080; 10-16Models 008-040; 1-8Models 105-133; 21-26TERMINALBOARDT3T2T1208-230V/3 phase/60HzM1M2M3FAN MOTORS460V/3 phase/60Hz Diagram 4. Typical Wiring Diagram for 208-230-460/3/60 TERMINALBOARDT3T2T1208-230V/3 phase/60HzGNDT2BOARDTERMINALT1M1C1C1M2C2FCCCOMNCC2M3C3FCCCOMNCC3FAN MOTORSCONTACTOR COILSTHERMOSTATS OR PRESSURE CONTROLSCONTACTORSCONTROL CIRCUIT* Models 049-080; 10-16Models 105-133; 21-26460V/3 phase/60Hz Diagram 5. Typ