Nach Entfernung der angeschwei.ten Verbindungsstellen der Ausblas-und Ansaugschlauche, nach Abschrauben der Befestigungsschrauben, hebe man den Kompressor, danach mache man ein Loch an der Unterseite des Gehauses und, indem man es kippt, lasse man das Ol in einen Behalter oder ein Fa. laufen, das an die Wiederverwertungs- bzw. Entsorgungsstelle fur wirkungslose Ole weiterzuleiten ist. Die verbliebenen Metallteile beinhalten Kupfer, Aluminium und Stahl und konnen daher der Verschrottung zugefuhrt

Teile einzeln bestellen. 105398 19 20 105398 TRAGBARE HOCHDRUCK-HEISSLUFTTURBINEN R BEBILDERTE ERSATZTEILLISTE B100CEH MODELL Motor- und Pumpenbaugruppe 1 2 3 23 19 9 10 16 11 12 15 25 27 24 28 20 22 21 30 31 17 14 14 35 36 32 26 13 18 4 5 6 7 8 7-2 7-1 7-5 7-4 7-3 7-6 43 42 41 33 34 37 39 40 44 38 29 10-1 10-2 10-3 10-4 10-5 10-6 10-7 10-8 10-9 10-10 10-11 10-12 10-13 10-14 10-15 10-16 10-17 10-13 BEDIENUNGSANLEITUNG Dieser Katalog enthalt die Ersatzteile fur Ihr Heizgerat. Bei der Bestellung v

When ordering parts, be sure to PARTS LIST provide the correct model and serial numbers (from the model plate), then the part number and description of the desired part. 70,000 BTU/HR KEY NO. PART NUMBER PART DESCRIPTION QTY. KEY NO. PART NUMBER PART DESCRIPTION QTY. 1 2 3 4 5 6 7 8 9 1010-1 10-2 10-3 10-4 10-5 10-6 10-7 11 12 13 14 15 16 17 1818-1 18-2 18-3 18-4 18-5 18-6 18-7 18-8 18-9 M51104-01 098511-54 102432-01 098512-44 M11084-29 M16660 M10908-2 HA3019 079673-06 ** HA3008 M10659-1 M10809-

102D (For Home Use Only) Listed _ „ (£)„.. Air Compressor SPECIFICATION CHART Model No. 102D Horsepower 3/4 SCFM @ 40 psig 2.9 SCFM @ 90 psig 2.1 Displacement CFM 4.0 Bore 1 3/4" Stroke 1 1/4" Voltage-Single Phase 110-120 Minimum Branch Circuit Requirement 15 AMPS *Fuse Type Quick Acting Amperage at Max. Pressure 10 Tank Size 2 Gallon *A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit the air compressor is operated

Control Flame- Reset Out Button Control Reset Button Flame-Out Figure 6 - Flame-Out Control Reset Figure 7 - Flame-Out Control Reset Button, 70,000 BTU/Hr Model Button, 100/150,000 BTU/Hr Models Continued 7 OPERATION Continued STORAGE PREVENTATIVE MAINTENANCE SCHEDULE To Stop Heater 1. Unplug power cord from outlet. To Restart Heater 1. Wait 2 minutes after stopping heater. 2. Repeat steps under To Start Heater, page 7. 1. Drain fuel tank. Note: Some models have drain plug on underside of fuel t

Improper use of heater can cause serious injury. Keep this manual for future reference. SECTION PAGE CONTENTS Safety Information .................................................................................... 3 Product Identification ............................................................................... 4 Unpacking................................................................................................. 4 Assembly .............................................................

RADIANT PANEL SYSTEM® PLANNING & INSTALLATION MANUAL (rev) ROTH HEATING SYSTEMS 5A. INTRODUCTION The Roth Radiant Panel System® was developed for the wood frame houses of the North American and Scandinavian markets. It was designed for easy installation over any new or existing sub-floor, wood or concrete, and for use with many different floor coverings, such as carpet, tile or hardwood. This is done without the structural changes needed to accommodate the additional load of lightweight concrete

4. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. Check with local automotive service stations that recycle oil. 5. If storing, store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. Item How Often How To Fuel tank Flush every 150-200 hours of operation or as needed. See Storing, Transporting or Shipping,column 1 Air

Periodic checks and adjustment of the opener are required to ensure safe operation. The model number label is located on the operator cover. As of date of manufacture, meets all ANSI/UL 325 Safety Standards and requirements for residential and commercial applications. ® TM H I G H L O W N OR M A L H I G H L O W N ORMA L UP FORCE DOWN FORCE Includes Lift-Master "Protector System" CONTENTS PAGE CONTENTS PAGE A review of safety alert symbols ..............................2 Safety reversing sensor i

Optional extra parts to equip heater with flame-out control. 27 100743 28 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 (2) 17 18 19 20 25 26 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 6 21 22 23 24 45 44 27 28 MOTOR & PUMP 100 EAI/EBI PFA/P 010 ILLUSTRATED PARTS BREAKDOWN 90,000 BTU/Hr 13-1 13-2 13-3 13-4 13-5 13-6 13-7 13-8 13-9 13-10 13-11 13-12 13-13 13-15 13-16 13-17 13-18 13-14 Motor and Pump Assembly BURNER HEAD 100 EAI/EBI PFA/P 022 8-2 8-6 8-5 8-4 8-3 8-1 Burner Head Assembly 8-7 This list co