Follow the instructions on the battery charger. SERVICE NOTE: Make sure you plug the battery charger into the connector with the handle attached to it. IMPORTANT: Make sure you have an appropriate charger for use on Gel cell batteries. Use only “voltage-regulated” or “voltage-limited” chargers. Standard constant current or taper current chargers MUST NOT be used. A temperature-sensing charger is recommended, as manual adjustments are never accurate and will damage any VRLA battery. B-18 - FORM

hergestellt wurden. GB The undersigned certify that the above NL Ondergetekende verzekert dat de mentioned model is produced in accordance bovengenoemde modellen geproduceerd zijn with the following directives and standards. in overeenstemming met de volgende richtlijnen en standaards. Manufacturer: Nilfisk-Advance Spa Authorized signatory: Franco Mazzini, General Mgr Date: Signature: Administrative Office: Address: Localita Novella Terza, 26862 Guardamiglio (LO) - Italy Phone: +39 0377 451124,

to persons are marked with this danger symbol. tips and instructions which structions to This indicates instructions these operating in- english Symbols used to mark Safety instructions in Before using the high-pressure This symbol is used cleaner, be sure to mark safety into also read the structions that must enclosed operat-be observed to preing instructions and vent damage to the ma- keep them within reach at all chine and its performance. times. 1 Important safety instructions For your own s

Edificio Central Park Herrera 1855, Office 604 Ciudad Autonoma de Buenos Aires Tel.: (+54) 11 6091 1571 AUSTRALIA Nilfi sk-Advance 48 Egerton St. P.O. Box 6046 Silverwater, N.S.W. 2128 Tel.: +61 2 8748 5900 E-mail: info@nilfisk-advance.com.au AUSTRIA Nilfi sk-Advance GmbH Metzgerstrasse 68 5101 Bergheim bei Salzburg Tel.: 0662 456 400-14 E-mail: info.at@nilfisk-advance.com BELGIUM Nilfi sk-Advance n.v-s.a. Riverside Business Park Boulevard Internationalelaan 55 Batiment C3/C4 Gebouw Bruxelles 10

Raise the squeegee tool off the floor, then unsnap the Center Latch (A) on the squeegee tool. 2 Remove the Tension Straps (B). 3 Slip the rear blade off the alignment pins. 4 The squeegee blade has 4 working edges. Turn the blade so a clean, undamaged edge points toward the front of the machine. Replace the blade if all 4 edges are nicked, torn or worn to a large radius. 5 Install the blade, following the steps in reverse order and adjust the squeegee tilt. To Reverse or Replace the Front S

Nilfisk C 120.3 Nilfisk C 125.3 Nilfisk C 120.5 X-TRA User Manual 128330335 Printed in China Copyright © 2010 Nilfisk, Division of Nilfisk-Advance A/S Index 1 Safety precautions and warnings .............................................3 2 Description ...............................................................................5 3 Before you start using your pressure washer ...........................6 4 Operating your pressure washer ..............................................7 5 Fields of

NOTE (Non AXP/EDS Models): For a consistent reduced flow of solution; open the Solution Flow Control Valve Lever (7) all the way and then turn ON the Smart Solutions™ / ECO Solution™ Valve (26). When the lever is in the “OFF” position; the machine operates conventionally; solution fl ow is determined by the Solution Flow Control Lever (7). When the lever is in the “ON” position; solution flow is controlled automatically. The Solution Flow Control Lever (7) should not be shut off, but is otherwis

The machine will restart after a few minutes when the thermal sensor has cooled. 4 2 Description 2.1 Application 2.2 Operation elements and model survey This high-pressure washer has been developed for domestic use within: - Car, motorbike, boat, caravan, trailer, patio/drive/flagstones, woodwork, brickwork, barbecue, garden furniture, lawn mower See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet with filter (2a) 3 High pressure connection 4 High pressure hose 5 Electr

Vary the pressure on the Drive Paddle (34) to obtain the desired speed. NOTE: Speed Control Knob (35) is used to control the maximum speed in either forward or reverse. 4 Press and hold the Solution Switch (B) for 5 seconds to pre-wet the floor. NOTE: This must be done prior to pressing the Scrub ON Switch (I). 5 Press the Scrub ON Switch (I) once for Regular Scrub or twice for Heavy Scrub mode. Hold this switch for 5 seconds for Extreme Scrub mode. Both the solution system and detergent (EDS