• The Balance Setpoint Limits can be adjusted according to the manufacturer’s specifications under “Balance Setpoint” – See Installation Settings. 3) When the RC-1000 makes a call for auxiliary heat, the heat pump compressor is turned off and the auxiliary heat is used exclusively. Heat Pump (2 Stage Heat / 1 Stage Cool) 9 876543 1 24VAC Common 24VAC "HOT" Auxilirary Heat Compressor Ground Fault Fan Compressor Relay Aux Heat Relay Fan Relay Fault Relay Reversing ValveEnergized in Cool Energized

To enter programming mode, press the Prog key 4 times. When in programming mode: 1. The item that is being programmed will flash. 2. The up arrow key (.) is used to increase the value. 3. The down arrow key (.) is used to decrease the value. 4. The Prog (>) key is used to advance to the next item. 5. The Hold (<) key is used to return to the previous item. 6. To exit programming mode, press the Mode key. The thermostat will automatically exit programming mode after 20 seconds of no key activity.

Under these conditions, the heat pump will run continuously and the auxiliary heat will cycle on and off as needed. If you wish to temporarily override Energy Efficient Control to heat as quickly as possible, press the Hold key. The RC-101 will use the Auxiliary Heat as needed to reach the heat setting, then resume Energy Efficient Control once the setting is reached. Remember to turn Hold off to resume programmed operation. 3 OPERATION To take advantage of all the benefits and features offered

This will allow you to have different heating and cooling settings on Saturday and Sunday, than you normally would have for weekdays (Monday Friday). When programming the time schedules, the weekday time schedule is programmed first. The Saturday time schedule is programmed second, and the Sunday time schedule is programmed last. 8 SETTING TIME SCHEDULES To view or change the programming time schedules of your thermostat, press and the Prog key four times. The weekday MORN time will flash. 1. Us

If the thermostat or system does not perform as stated above, recheck all wiring -See Troubleshooting Tips. INSTALLER SETUP This section describes the items that the installer must setup as part of the thermostat installation. The Installer Setup mode is used to configure the general operating parameters of the thermostat. When in Installer Setup mode: 1. The small digits on the top of the display are the item number. 2. The large blinking digits in the center of the display are the value of the

7-AUTO AUTOis displayed when in automatic changeover mode. 8-HEAT HEATis displayed when the system is in Heat mode. 9-FAN FANis displayed when the fan is set to run continuously. 10-OFF OFFis displayed when the system is in the Off mode. 11-REMOTE REMOTE is displayed when the last command received by the thermostat was sent by a remote system. 12- Period Indicators MORN, DAY, EVE, or NITE is displayed when scheduled temperature changes are made by the thermostat programs. 13-HOLD HOLDis displaye

6-COOL COOL is displayed when the system is in Cool mode. 7-AUTO AUTO is displayed when in automatic changeover mode. 8-HEAT HEAT is displayed when the system is in Heat mode. 9-FAN FAN is displayed when the fan is set to run continuously. 10-OFF OFF is displayed when the system is in the Off mode. 11-REMOTE .. REMOTE is displayed when the last command received by the thermostat was sent by a remote system. 12- Period Indicators MORN, DAY, EVE, or NITE is displayed when scheduled temperature cha

FCC This thermostat has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This product generates and can radiate radio frequency energy. Due to its low power design, it is unlikely to interfere with radio and TV communications. If it is suspected of doing so, the user is encouraged to try to correct the problem by reorienting the receiver's antenna, moving the receiver away from the product, or consulting an experienced radio/TV t

3-DESIRED DESIRED is displayed when the temperature display shows the desired temperature setting. 4-OUTSIDE OUTSIDE will be displayed when the temperature display shows the outdoor temperature. The outdoor temperature will be displayed every 4 seconds. 4 5-. .. The . .. is displayed when the heating or cooling system is running. 6-COOL COOLis displayed when the system is in Cool mode. 7-AUTO AUTOis displayed when in automatic changeover mode. 8-HEAT HEATis displayed when the system is in Heat m

All Rights Reserved CONTENTS INTRODUCTION ..................................1 DESCRIPTION ....................................1 MAINTENANCE ...................................1 OPERATION .....................................2 DISPLAY ........................................4 FILTER REMINDER ................................6 ANTICIPATION ...................................6 SETTING THE CURRENT TIME AND DAY ...............7 PROGRAMMING ..................................8 SETTING TIME SCHEDULES ...