This action will erase any previous signal that was learned by the control board and prepare it to learn your transmitter signal. At this time have your transmitter ready to transmit. STEP 2: Press and quickly release the Learn Enable button on the Super Station. The red LED light on the rear panel of the power head unit (and the work light) will illuminate and remain on, the control board is now ready to learn the signal from your transmitter. Within a twenty second time frame, press the button

Product Features ................................................... 2 Component Identification..................................... 3 Identify Your Door Type ........................................ 3 Important Installation Instructions........................ 4 Assembly Instructions........................................... 5 Installing the Opener ............................................. 7 Mounting the Front Bracket ................................ 7 Mounting the Power Head..............

“OFF-ON” will prevent inadvertent operation of the door from any other push button, radio or keyless entry device. It will also as additional protection from unwanted operation during absence of the owner. This feature is to be activated only when the door is at the full open or close position and never while the door is moving. 2. “LIGHT” button allows the convenience light to be turned on and stay on until turned off by a second push of the button or activation of the door cycle. 3. “UP/DOWN”

• ADJUST THE SENSITIVITY ADJUSTMENTS ENOUGH TO ALLOW THE DOOR TO OPERATE, BUT NOT SO FIRMLY AS TO EXERT EXCESSIVE PRESSURE ON AN OBSTRUCTION BEFORE REVERSING. • AFTER INSTALLING THE OPENER, THE DOOR SHOULD REVERSE WHEN IT CONTACTS A 1-1/2" HIGH OBJECT (A PIECE OF STANDARD 2 X 4 BOARD LAID FLAT) ON THE FLOOR. B: IMPORTANT INSTALLATION 7 WARNING SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEAT

Use a minimum 22 gauge solid "trace" wire for interconnect. C. Run a wire pair (20 or 22 gage solid wire) from the receiver position (unit with "LED" light in the front, may be either side of the door) back to the rear bulkhead of the garage door opener. NOTE: Leave about 12” of extra wire at the receiver end and about 24” of extra wire at the opener end. D. Strip approximately 5/16” from each wire end at the photosystem units and at the opener. E. Using two (2) wire nuts (supplied), connect the

Write the code that you matched from your transmitter or receiver in the grids below. 1 2 3 4 5 6 7 8 9 + / On BUTTON Zero BUTTON - / Off BUTTON - PUT THE TRANSMITTER IN PROGRAM MODE 1. First, press and hold the + 1a. First, press and hold the - button. The Red LED will turn on. Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons

The 831E is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. The receiver is powered from the operator’s 24 VAC transformer. The antenna is removable and may be moved (using coaxial cable) to a new location for better RF reception. When receivers have to be installed in close proximity to each other (such as Fire Stations), master/slave units may be used to reduce the potential for receiver cross-talk. •

The radio frequency of the remote controls is fixed and tuned at the factory; adjustments are not required and should not be attempted by the end user. WARNING Keep transmitters and remote controls out of the reach of children. Do not let children play with or use the transmitter or remote controls. Unexpected door operations can cause personal injury or property damage. Do not place transmitter where the buttons can be accidentally or unintentionally activated. Features of the Quik-Code Wireles

2 WARNING HIGH VOLTAGE ONLY A QUALIFIED TECHNICIAN SHOULD SERVICE THIS GATE OPERATOR PERIODICALLY TEST SENSITIVITY OF OVERLOAD *** READ MANUAL *** DATES DATE TESTED DATE TESTED DATE TESTED DATE TESTED SERVICED LOG DATE OVERLOAD TEST Pre-Installation Notes................................................... 3 Operator Class Designation ................................... 3 Section A: Gate System Design/Installation ............. 4 Section B: Preparing the Site .....................................

In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after July 1, 1998. For Information: Phone 610-873- 6900 info@allstarcorp. com FAX 610- 873-6953 all