15- ENG D25804 TROUBLE SHOOTING GUIDE PROBLEM CAUSE CORRECTION Engine will not start (see Engine Manual for further engine troubleshooting) No fuel. Low oil (if equipped with low oil shutdown). Pressure builds up after two pulls on the recoil starter or after initial use. Not primed or choked. Spark plug wire not attached. Engine ON/OFF switch in OFF position (If applicable.) Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long perio
CALIFORNIA PROPOSITION 65 This product or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. REMINDER: Keep your dated proof of purchase for
El fusible o cortacircuito esta quemado El alambre se enrolla en 1. La boquilla de la pistola no es la bobina del tamano adecuado 2. El forro interno de la pistola esta atascado o danado 3. La boquilla de la pistola esta atascada o danada 4. La bobina esta desgastada 5. No tiene suficiente tension La boquilla se pega a la Hay escorias dentro de la boquilla Limpie la boquilla de la pistola superficie de trabajo de la pistola La pinza de conexion a Mala conexion Cerciorese de que todas las conexio
© 2008 IN614205AV 11/08 Oilless Compre s s o r s General Safety I n f o rmation ( C o n t i n u e d ) 6 . Do not stand on or use the pump or unit as a handhold. 7 . Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using. 8. Check all fasteners at frequent intervals for proper tightness. Motors, electrical equipment and controls can cause electrical arcs that will ignite a fla
Holding the work by hand or against the body is unstable and is able to lead to loss of control. b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed. c. Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. d. Disconnect the tool from the air source before making adjustments, doing tool mai
Use of improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure: 1. That the size of the cord is at least as specified in chart titled “Minimum Wire Size (AWG) of Extension Cord for Recipricating Saw.” 2. That the pins on plug of extension cord are the same number, size and shape as those of plug on saw. 3. That the extension cord is properly wired and in good electrical condition. 4. If an extension cord is to be used outdoors it mu
Voltage drop in the extension cord may significantly degrade performance of the welder. Welding accessories for the welder are inside wire feed compartment. 1. Place handle assembly on welder, aligning two holes in plastic ends with threaded holes in welder housing (Fig. 2). 2. Insert screws through cord wraps and handle ends and fasten into cabinet. 3. Attach cylinder base to unit as shown (Fig. 3). 1. Loosen hex bolt/nut on work clamp. 2. Insert cord (labeled ‘work clamp’ on the front panel of
Long power cords and extension cords draw additional power. Keep cords at minimum possible length. Installation for Stand-by Use Precautions must be taken to prevent electrical back feeding into utility systems. This requires isolation of the electrical system. To isolate the electrical system, perform the following procedures: 1. Turn off the main electrical system switch prior to connecting the generator. 2. In accordance with national and local standards, a double throw transfer switch must b
Harrison, OH 45030 U.S.A. No. de Numero del Ref. Descripcion Repuesto Ctd. 1 Lanza regulable PM035101AV 1 *2 Lanza turbo PM022621AV 1 3 Manguera PM012902AV 1 4 Pistola PM037201AV 1 5 Niple adaptador PM022100AV 1 6 Conector rapido PM020600SV 1 7 Limpiador de puntas PM008500AV 1 8 Aplicador de detergente PM014700SV 1 * 9 Juego de ruedas (2) PM014100SJ 1 *10 Mango PM014200SV 1 *11 Tapa de la caja de herramientas HV601500SV 1 *12 Caja de herramientas HV601600SV 1 * Equipo opcional, tal vez no se sum
Refer to motor name plate for electrical ratings and specifications. 3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives minimum recommended wire sizes for compressor installations. MiniMuM pipe Size for CoMpreSSed Air line CfM length of piping System 25 feet 50 feet 100 feet 250 feet 10 20 40 60 100 1/2 inch 3/4 inch 3/4 inch 3/4 inch 1 inch 1/2 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 1 inch 1