1. Power switch in OFF position or faulty. 2. Bin signal switches in OFF position or faulty. 3. Faulty bin thermostat. 4. Faulty transformer. 5. Icemaker related problem. 6. Faulty run capacitor. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. If problems persist after following this basic

After the time delay the machine will restart and the TIME DELAY, HI AMP, and SERVICE LED’s will clear. LO WATER: During operation, the water level cycles between the normal low and normal high sensors. Should the water be shut off to a running machine, a soft error will occur. The error sequence is as follows: During operation, the water level falls to the normal low sensor, and when it does the water feed solenoid is energized. If water is not detected at the normal low sensor within 120 secon

drains electrical conn. 6" min 17" (432 mm) 18.875" (479mm) 18.875" (479mm) ice transport tube 12" min counter top 32.375" (823mm) Side View 24.62" (626mm) 30" (762mm) 15" (381mm) 10" (254mm) 2" (51mm) ice waterbath (VU300B only) 8.5" (216mm) ice transport tube entry 27.5" (699mm) bin signal power 3/4" drain nipple 1/2" ID drain tube beverage lines 6 Dual-sided dispensers Required clearances 60" (1524mm) above counter for installation if dispenser will be dropped into counter 49" (1245mm) above

It is the responsibility of the technician to ensure that these requirements are met. Recharging icemaker to other than factory specifications will void the warranty. R404A icemaker charge specifications Model Charge Refrigerant type HCC1000A (air-cooled) 24oz (652g) R404A HCC1000W (water-cooled) 15oz (426g) R404A Refrigerant replacement requirements 1. Non-contaminated refrigerant removed from any Follett refrigeration system can be recycled and returned to the same system after completing repa

Es kann insbesondere dann öfters dazu kommen, wenn die Eiswürfel eine Zeit lang gelagert worden sind, ohne dass sie benutzt wurden. Verwenden Sie die beigelegte Rührstange um die Brücken zu zerbrechen (beachten Sie dabei die unten aufgeführten Vorsichtsmaßregeln). 1. Alle Eiswürfel von den Seiten und der Mitte des Behälters abschlagen. 2. Alle etwaigen Brücken, die sich in der Mitte gebildet haben, abschlagen. 3. Mit der Rührstange stochern, um zusammen geklumpte Eiswürfel loszubrechen. Die

(407mm) (458mm) 1000 series - 28.6" min. (727mm) 1400 series - 31.6" min. (303mm) 24.5" min. (623mm) No Lip . . . . . 1.75" (45mm) CROSSBRACE Undercounter installation detail – Horizon 1000 & 1400 series CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifi cations on facing page (4.1) 10 self-contained DROP-IN • SATELLITE-FILL Ice transport tube Install the ice t

START CAPACITOR COMPRESSORSTART RELAY (SEE NOTE #1) HI PRESSURESAFETY SWITCH P S COMPRESSOROVER-LOAD COMPRESSOR R START RUN CONDENSERFAN(AIR COOLED ONLY) WHT WHTBLK BLK #4 WHT RED GROUNDSCREW 115 60HzFROMDISPENSER BOX ICE MACHINEPOWERCONNECTION L2 DRIVE L2 FAN COMP L2 L2 L2 L1 L1 WHTBLKGRN EARTH WHTBLKBLK REDORG SWITCH COMP 2ND B-T B-E WTR 60M 20M C POWER RESET SENSOR WATER DR WATER SENSOR COMPRESSOR SWITCHI = COMP ONO = COMP OFF WATER RESERVOIR ICE MACHINE PCB VAC LINE VAC 24 BIN SIGNALCONNECTI

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Plumbing and clearance requirements. . . .. . . .. . . . . . . . . . . . . . . . .4 Field wiring diagrams. . . . .

5. Icemaker related problem. 6. Faulty or disconnected wiring. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to Icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. 15 Symptom Carbonator pump not turning on. Carbonator pump is not turning off. Carbonation system is not carbonating. Carbonation system is producing excessively carbonated beverag

Internal connections 7 • Remove twist tie • Carefully pass plug thru opening and plug into wall outlet 7.3 Power cord . . • Slide icemaker into louvered docking assembly . • Insert ice transport tube all the way into coupling and tighten nut firmly . 7.1 Ice transport tube . . . . • Insert potable water line into valve . • Push drain line over hose barb on back of evaporator mount . 7.2 Potable water and drain lines Air-cooled icemakers – follow steps 7.1 through 7.4. • Position plate into openi