9Transmission Quadshift gear ranges -All Models Powershift gear ranges -Models 435, 485, 535 48101214162618202224MPHGEAR48101214162618202224MPHGEAR48101214162618202224MPHGEAR LOW RANGE MEDIUM RANGE HIGH RANGE 1 2 3 4 5 6 7 8 9 10 11 12 LOW RANGE MEDIUM RANGE HIGH RANGE 1 2 3 4 5 6 7 8 9 10 11 12 engine speed for peak horsepower and torque, or for constant PTO operation. The next field Farms have expanded and moving to the next field is no longer as simple as crossing the road. With that in mind,

III, 3-point Hydraulic requirements 13 - 22 GPM 13 - 22 GPM 13 - 22 GPM 20 - 32 GPM 20 - 32 GPM 10 GPM 2000 psi min. 2000 psi min. 2000 psi min. 2000 psi min. 2000 psi min. 1000 psi min. System controls & drive Hydraulic load sensing Hydraulic load sensing Hydraulic load sensing Hydraulic load sensing Hydraulic load sensing PTO w/shear pin Block flow adjustable Block flow adjustable Block flow adjustable Block flow adjustable Block flow adjustable Fan 4-blade 4-blade 4-blade 4-blade 4-blade 4-bl

A Buhler hammermill does the job quickly and economically, grinding as much as 75 bushels per hour. An adjustable motor mount fits most 5 to 7.5 horsepower electric motors. The sliding feed gate controls the amount of grain entering the mill and an optional magnet removes nails and other metal objects from grain and prevents damage to the hammermill. An optional discharge hopper makes it easy to move processed grain. The hammers are made from high quality carbon steel for extralong life. They c

c) Turn spout to center forward position and clamp cable to cable anchor on far side of spout using clamp (#84). 7. Mounting blower on tractor: a) Mount the blower on a tractor with a category 1 or category 2 hitch. b) Using tape or bright colored marking pen, mark on the outer shields the position where the shaft is completely pushed together and the position where you have a 4" overlap. Watch these marks when moving the blower through all possible operating angles to see that the PTO shaft sta

85” Snowblower TABLE OF CONTENTS DESCRIPTION PAGE Warranty ......................................................................1 Safety Instructions .......................................................2 Safety Sign Locations..................................................3 Assembly Instructions..................................................4 Operating Instructions..................................................5 85” Allied Snowblower Drawings..................................6 85” Al

TURN SIGNALS Move the stalk to position 1 to indicate a right-hand turn. Move the stalk to position 4 to indicate a left-hand turn. The turn signal warning light (and trailer lights, if connected) will also flash when the signals are operated. HEADLIGHTS HIGH/LOW BEAMS With the headlights switched on, pull the stalk to position 3, to change from one beam to the other beam. HEADLIGHT FLASH With low beam headlights on, pull the stalk to position 2, to flash the high beams. Release the stalk to ret

• Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods. • Always follow the engine manual instructions for proper start-up procedures when returning the unit to service. • Never store the machine or fuel container inside where there is an open flame, such as in a water heater. Allow unit to cool before storing. • Shut off fuel while storing or transporting. Do not store fuel near flames or drain indoors. • Keep all ha

IMPORTANT FACTS: Buckets and Bucket Tines Carry No Warranty Bent Spears Carry No Warranty Snowblower Fan Shafts Carry No Warranty Mower Blades Carry No Warranty Portable Auger Parts Have Two (2) Year Warranty Loader Parts Have Two (2) Year Warranty IMPORTANT NOTE: This warranty does not apply to rentals Cultivator 2 INTRODUCTION The Buhler Farm King Cultivator features a solid welded frame construction with 2” x 2” x .250 wall tubing. There is a simple one bolt shank allowing for easy spacing ad

I Cat. I, optional fit Cat. II Heavy-duty oil bath (540 RPM) Heavy-duty oil bath (540 RPM) Heavy-duty oil bath (540 RPM) #60H #60H #80H #80H #100H #100H #100H #100H 196 RPM or 880 ft/min 203 RPM or 865 ft/min 196 RPM or 880 ft/min 4 ." 7 ." 6 ." 8 ." 5" 8" 15" n/a Slip clutch, shear bolt optional Slip clutch Slip clutch ." x 2 ." ." x 2 ." ." x 2 ." ." x 2 ." 5/16" x 3 ." 5/16" x 3 ." 5/16" x 3 ." 5/16" x 3 ." 5 flanges 6 flanges 6 flanges 8 flanges 5 flanges 6 flanges 7 flanges 8 flanges 4 tine