Login:
Sortierung : Dateiname ↑   heruntergeladen   Bewertung   Dateigröße ↑  

Jonsered ECS-3301

heruntergeladen wurde: 1Dateigröße: 619 kb    Hersteller: Jonsered  
Kategorie: Kettensägen

Make sure that the fuel is well mixed by shaking the container, before fueling. 5 custsvc@tanaka-ism.com Owner.s ManualECS-3301/3351 ECS-3301/3351 CHAIN OIL (Fig. 2-1 B) Fill the chain oil reservoir (2). Always use good quality chain oil. When the engine is running, the chain oil is automatically discharged. NOTE! When pouring fuel (1) or chain oil (2) into the tank, place the unit with cap side up. (Fig. 2-1B) (2) ADJUSTMENT OF CHAIN OIL SUPPLY The chain oil quantity discharged through the lubr

Jonsered 2159

heruntergeladen wurde: 1Dateigröße: 2 mb    Hersteller: Jonsered  
Kategorie: Kettensägen

Recommended idling speed: 2 700 rpm. Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the chain stops. Do not use the saw until it has been properly adjusted or repaired. Fine adjustment • When the saw has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the air filter should be cl

Jonsered FC 2145

heruntergeladen wurde: 23Dateigröße: 2 mb    Hersteller: Jonsered  
Kategorie: Gartengeräte

Oiling the air filter Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter.You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect i

Jonsered CS 2141S

heruntergeladen wurde: 0Dateigröße: 2 mb    Hersteller: Jonsered  
Kategorie: Kettensägen

1 Filing angle 2Cutting angle 3 File position 4 Round file diameter It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain. See instructions under the heading Technical data for information about sharpening your chain. ! WARNING! Departure from the sharpening instructions considerably increases the risk of kickback. Sharpening cutting

Jonsered LT2115A

heruntergeladen wurde: 54Dateigröße: 1 mb    Hersteller: Jonsered  
Kategorie: Handrasenmäher

LT2115A PRODUCT NO. 960 11 01-82 401433 11.14.05 VB PRINTED IN THE U.S.A. REPAIR PARTS TRACTOR - MODEL NO. LT2115A (96011018200), PRODUCT NO. 960 11 01-82 SCHEMATIC 03054 (197428) BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACKBROWN BLACK BLACK BLACK STARTER M SEAT SWITCH (NOT OCCUPIED) GROUNDING CONNECTOR ATT'MENT CLUTCH (CLUTCH OFF) CLUTCH / BRAKE (PEDAL UP) SOLENOID BLACK A AMMETER RED G B S M A1 A2L HOUR METER

Jonsered ECS-370

heruntergeladen wurde: 3Dateigröße: 606 kb    Hersteller: Jonsered  
Kategorie: Kettensägen

Jonsered ECV-4501

heruntergeladen wurde: 3Dateigröße: 618 kb    Hersteller: Jonsered  
Kategorie: Kettensägen

If the cutting attachment still rotates after idle speed adjustment, contact your service workshop. NOTE! The L and H screws should only be adjusted by an Authorized Tanaka Dealer. The standard openings (returns) of L/H screws from lightly seated positions are as follows: WARNING! When the engine is idling the cutting attachment must under no circumstances rotate. NOTE FOR THE US MARKET!! (Fig. 3-1B) We would like to inform that the machines, which carry the following label on the unit are diffe

Jonsered CS 2145S

heruntergeladen wurde: 6Dateigröße: 2 mb    Hersteller: Jonsered  
Kategorie: Kettensägen

3 Take great care when removing small branches and avoid cutting bushes (i.e. cutting many small branches at the same time). Small branches can be grabbed by the chain and thrown back at you, causing serious injury. 4Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground. English – 21 22 – English WORKING TECHNIQUES 5 Take great care when cu

Jonsered SM 2186

heruntergeladen wurde: 9Dateigröße: 2 mb    Hersteller: Jonsered  
Kategorie: Kettensägen

29) Install the chain and bar on the motor unit as follows: 1.Secure the chain around the motor unit’s sprocket. Ensure that its teeth correspond with the direction of rotation according to the arrow (A). 2. Position the bar and thread the chain around the bar. CAUTION! Ensure that the tip of the tension screw’s nut (B) fits into the hole on the bar. 3. Install the guide (C) and loosely tighten the two bar bolts (just so that there is no play on the bar). 4. Adjust the chain using the tension sc

Jonsered ECS-3351

heruntergeladen wurde: 0Dateigröße: 619 kb    Hersteller: Jonsered  
Kategorie: Kettensägen

• Stop engine before removing fuel cap. • Empty the fuel tank before storing the unit/machine. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store unit/machine and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. WARNING! Anti-vibration systems do not guarantee that you will not sustain white-finger disease or carpel tunnel syndrome. Therefore,





Kategorien