110621 A IMPORTANT SAFETY INSTRUCTIONS AND OTHER NOTICES • This label printer complies with the requirements in Part 15 of FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interface to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference. • Place the printer on a flat, firm and solid surface. • Do not place the printer near a heat source or near water. • Refer to the speci

Input Capacity: a) Standard 250 sheets tray x 1 100 sheets multi bypass tray* *Bypass tray and duplex unit do not work together. b) Options Paper Bank: 500 sheets x 1 Max total capacity: 850 sheets 5. Output Capacity: 250 sheets (internal tray) 6. Paper size / weight: a) Size: Standard Tray: A5 (LEF), A4 (SEF), 5 1/2” x 8 1/2” (LEF), 8 1/2” x 11”(SEF) Bypass Tray: A6 (SEF) – A4 (SEF), 5 1/2”x 8 1/2” - 8 1/2”x 14”(SEF) Irregular size: 90 - 216 x 139 - 600 mm 3.54” - 8.5” x 5.48” – 23.62” Duplex:

387002, Rev. E ® ™ AMT ACCEL-6300 P R I N T E R S E R I E S User's Guide Unpacking Set Up Loading Paper Control Panel Cleaning & Maintenance Solving Problems Bottom-Feed Tractors Bar Codes Interfaces Code Sets Specifications Document No. 387002 .. Revision E AMT Datasouth Corp. 4765 Calle Quetzal Camarillo, CA 93012 TEL: (805) 388-5799 FAX: (805) 484-5282 WEB: amtdatasouth.com User's Guideii Preface User's Guide Preface Thank you for selecting an AMT Datasouth® ACCEL™-6300 series printer. Using

h width multiplier ‘1’ to ‘9’ and ‘A’ to ’ O’. ‘0’ stands for default. v height multiplier ‘1’ to ‘9’ and ‘A’ to ’ O’, ‘0’ stands for default. eee bar code height This is ignored for box, line and graphics. It represents point size for font ‘9’ and symbol set for Courier font** . yyyy Y coordinate xxxx X coordinate depends on object types User's Guide 53 Object Command Structure Description L : line (if t is ‘X’) Lwwwhhh www : width, hhh : height. L : line (if t is ‘X’) lwwwwhhhh wwww :

The value of 4 lines per inch .......... ESC A SI 1B 41 0F 27 б5 15 variable n defines the line spacing distance: 6 lines per inch .......... ESC A LF 1B 41 0A 27 б5 10 8 lines per inch .......... ESC A BS 1B 41 08 27 б5 8 Line spacing = n x 1/72-inch (Epson JX & IBM XL24) 12 lines per inch........ ESC A ENQ 1B 41 05 27 б5 5 Line spacing = n x 1/60-inch (Epson LQ-2550) Note: When the IBM XL24 emulation is active, the Set Vertical Units sequence forces the vertical spacing unit to either 1/7

D Contents... Table of Introduction.............................................................. i 1. Before Using the ATB Printer.........................1-1 1.1 Checking the Package ....................................................... 1-2 1.2 Names and Functions ........................................................ 1-3 2. Operation..........................................................2-1 2.1 Connecting the ATB Printer..............................................2-2 2.2 Turning the

108738 Rev. C NOTICE There are no user-servicable parts inside the side access panel on theCodewriter 4500 Series products. Do not attempt to open the sideaccess panel without first turning off the power to the unit, disconnecting the power cord from the unit, and disconnecting allcommunication cables. All service procedures should be performed by a qualified servicetechnician. NOTICE This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. Thi

NOTE To eject a cut sheet form for any reason, press the Form Feed Key. Figure 3-7: Tear Off Bar Scale 3-10 Forms Handling User’s Guide NOTE If forms length is between 4.5” and 6.0”, verify that the Vertical Gap Position Feature is set to 0.0” (located under M8 Form Thickness in the setup mode). See Section 4.6 for further instructions on how to change this setting. Failure to set Vertical Gap for these forms may cause trailing edge of form to catch under guide during loading. Figure 3-8: Loadin

20 Switch, Indicators and Connections....................................................................... 20 Label Sensor Calibration Procedure ...................................................................... 21 Printer's Internal Self Test Procedure and Configuration Report .......................... 22 Resetting the Printer to Factory Default Settings .................................................. 25 Entering into HEX Print mode.....................................................

105856 REV. D INTRODUCTION Your new multimode matrix printer offers bidirectional logic-seeking printing at 400 cps in draft mode, memo quality printing at 180 cps and up to 120 cps in near-letter-quality correspondence mode. Because of its multimode capabilities, this printer is suited for applications where multiple printers would otherwise be required. True lower case descenders and simultaneous underlining are possible. An adjustable printhead gap accommodates forms up to six parts in thic