To select Special Peak mode, press and hold then press . While in this mode the Peak flag will flash. Note: While tracing cables in any mode, keep the Receiver handle in line with the suspected cable path. See section Initial Receiver Configuration (Page 3) to set the power frequency to 50 Hz or 60 Hz. The Receiver can be tuned to locate 3 different harmonics of the chosen power frequency. H50 Hz or H60 Hz (high harmonic): Best for general locating of passive power. L50 Hz or L60 Hz (low harmoni

When the voltage magnitude is sufficient to impair the accuracy of the ohms measurement, only voltage will be displayed. If the voltage is AC, a sine wave will be visible on the display. If a high AC voltage is detected, a rapid beeping tone will be heard. Page 6 Press to select Trace mode. Press again to select one or all of the four frequencies. The display will alternate between displaying the selected frequency and the output signal current. It is best to choose the lowest frequency for dire

Press only when a marker is detected and the signal is too strong. To search for a new marker, reset the Receiver gain to the initial setting by turning its power OFF and back ON, or pressing and then re-selecting the Peak mode. Refer the EMS Marker Locating Accessory operating instructions for further information. Page 17 TONING AERIAL FAULTS Transmitter Setup Perform a battery test; then with the Transmitter off, plug the direct connect cable into the front panel jack. If fault is a shorted pa

• Press LO to cancel Local mode and switch to DX (distance) mode. • The “ST” (stereo) indicator lights up when the tuned-in station is broadcasting in stereo and the reception is good. FUNCTION button Each time you press FUNCTION, the unit switches to one of the following modes, in cyclic order. * CD Play mode (available while a CD is in the unit) ** CD Changer Play mode (available while the optional CD changer is connected) PRESETTING STATIONS To preset stations automatically (Auto Memory) 1 P

Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. lADC-M55 Seria’ ‘0 ~ Welcome Thank you for your purchasing thw AIWA product. To optimize the performance of this unit, please read through this manual carefully. lTABLE OF CONTENTS nFEATU13ES Tracks from 6 CDs stored in the disc magazine can be selected and played. . Horizontal, vertical, slanted or suspended Installation can be made NOTE This equipment has been tested and found to comply with the limits for

Do NOT attach paper or tape etc. to a disc. . Do NOT expose the discs to direct sunlight or excessive heat. Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth. There may be burrs left on the inner and outer edges of a brand-new disc. The burr may cause the malfunction of the unit or sound dropout. To prevent these problems, if the burr is left on the disc, be sure to remove them with a ball-point pen, etc. as illustrate

Remove these screws before installation. Retain these screws and replace them in the original positions if the unit is transported for service or maintenance. Mounting angle setting levers Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed. Mounting angla setting levers Insert a pointed object such as a screw driver or ball-point pen, etc. into the low spot of the lever and slide the lever to the position from among HO

2). • Den.Tonarm durch Umklappen der Tonarm-Verriegelung GE] entriegeln. • Die Lift-Taste CUEING IM. .mT 0 drücken zum Abheben des Tonarms von seiner Stütze (▼)• • Den Tonarm über die gewünschte Stelle der Platte führen. • Die Lift-Taste CUEING Xi »T [4] nochmals drücken, um die Abtastnadel auf die Platte abzusenken. Kehrt derTonarm augenblicklich auf seine Stütze zurück? Dann wurde versehentlich vorher die Taste REJECTgedrückt. Sobald der Plattenteller gestoppt ist, können Sie ihn wieder

Cet appareil vous donnera encore plus de satisfaction si l’utilisation et l'entretien sont suivis selon le mode d'emploi. Malgré tous les soins apportés, l'apparition de défauts n'est pas exclue. Dans ce cas, nous vous senons reconnaissants de bien vouloir vous adresser directement chez votre vendeui muni du passeport de l'appareil ainsi que de la facture s'y reportant_ 6ARANZIA PER LA SV1ZZERA Gli apparecchi Philips sono prodotti con materiali di prima qualité e assembîati con la massima cura