Stimmen - 4, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Remove these screws before installation. Retain these screws and replace them in the original positions if the unit is transported for service or maintenance. Mounting angle setting levers Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed. Mounting angla setting levers Insert a pointed object such as a screw driver or ball-point pen, etc. into the low spot of the lever and slide the lever to the position from among HORIZONTAL, 45°, and VERTICAL positions. Notes . Be sure to eject the disc magazine when you set the levers. l Be sure to set both levers to the same position. . Be sure to set the levers exactly at the position (notch). If the lever is deviate from the position, the sound may drop out. . Care must be taken when you mount the unit at the angle of lower than level. The diet magazine may drop if you eject the magazine. . Do NOT turn over the unit or slide the lever when the unit is activated. Doing so may damage the mechanism or the discs in the unit. . The mounting angle setting levers on each side of the unit are factory-set to the HORIZONTAL position. . When you complete the setting, attach the supplied adhesive labels @ over the slots. ENGLISH 4 h INSTALLATIONS Horizontal installation Construction For details on @@@..., see page 3. The effective angle of the unit. Note If the mounting surface needs to be strengthened, secure the plate brackets @to the bottom surface of the car trunk, etc. with the tapping screws (not supplied). 2 Deciding the position 3 Removing temporarily The position of the lever. 4 Making holes in the carpet 5 Completion Vertical installation Construction For details on @@@..., see page 3. Note l If the mounting surface needs to restrengthened, l If installation space is narrow, bend the plate bracket secure the plate brackets @ to the bottom surface @ back and forth along the perforated line to break off of,the car trunk, etc. with the tapping screws (not the end. supplied). Deciding the position Making holes in the carpet 24 plate @if it n9. Removing temporarily Completion 3 — 5 ENGLISH 6 ~ INSTALLATIONS Suspended installation Caution Before drilling the holes, make sure that there is When installing the unit in the trunk below the nothing on the other side of the mounting surface. package tray, observe the following. Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the deck lid. Construction For details on @@@..., see page 3. The effective angle of the unit. \’-=.“d: -0 The position of the lever. !“@@ ‘n \ @Jw -’ 4!3 H-L FIN 1 — YF 2 Making holes 3 Completion Tepping screws are not supplied Slanted installation Note on the brackets@ Be sure to set the To save installation space, you can place the 15“ mounting angle brackets @ inside out, as illustrated below. 15“ setting levers to the 45° position. 45” .. A 7 ENGLISH ~ CONNECTIONS This unit is designed only for AIWA brand car stereo. Therefore you can not use the unit with other brand’s equipment. + r to AIWA brand car stereo Caution Be sure to disconnect the ground wire terminal the car battery before making a connection order to prevent short circuiting. of in Note Use only the supplied unspecified connecting noise. connecting cable may cable. Using an cause background ENGLISH 8 , HOW TO USE How to use a compact disc magazine 1. With the label side up, insert a disc all the way *& a 6 discs, one in each disc tray t To remove a disc, pull part@ in the direction Recorded side of the arrow aa illustrated. 2 Open the 3 A INSERT A (eject) button Dlac magazine Insert the magazme (which has tIeen taken To remove the magazine, press the ~ button and Pull out the disc magazme. out of the unit) fv’mly wkh the .4A mark visible on the top side. 4 Close ~ SPECIFICATIONS Notes on the disc magazine Be sure to place a disc on the disc tray with the label side up. If a disc is not set properly, it may cause damage to the unit. Disc magazine 0 The disc tray may be taken off from the magazine if you pull the tray forcibly. If the tray is taken out, put it back into the magazine as illustrated. Be sure that both ends of the tray are aligned to the grooves of the magazine correctly. Compact disc changar System Compact disc digital audio system Frequency response 5 Hz – 20 kHz Wow and flutter Below measurable limit Si9naI to nOiSe ratio 91 dB or more outputs Line output (for changer connector only) Operating temperature –1o“c to55“c Dimensions 244 x63x 169 mm (w/h/d) (9 5/8X 2 1/2 x 6 5/8in,) Weight 1.8 kg (3.96 Ibs.) Power requirement 12 V DC car battery (negative ground) WA converter 1 bit DAC, 8 times over sampling Sampling rate 44.1 kHz Disc size 120 mm Supplied accessories Disc magazine (1) Mounting kit (1 set) Connecting cable (5 m) (16.4 ft.) (1) Design and specifications are subject to change without notice. l Be sure all the trays are set in the magazine when using the unit. ENGL/SH 10 Bienvenido...