Stimmen - 5, Durchschnittliche Bewertung: 4.6 ( )

Hersteller: Allstar Products Group Dateigröße: 1.24 mb Dateiname: Unterrichtssprache:

Use a minimum 22 gauge solid "trace" wire for interconnect. C. Run a wire pair (20 or 22 gage solid wire) from the receiver position (unit with "LED" light in the front, may be either side of the door) back to the rear bulkhead of the garage door opener. NOTE: Leave about 12” of extra wire at the receiver end and about 24” of extra wire at the opener end. D. Strip approximately 5/16” from each wire end at the photosystem units and at the opener. E. Using two (2) wire nuts (supplied), connect the wire ends at the ALL-CLEAR™ Photosystem transmitter to the pigtail wire ends coming out of the transmitter unit. Although not required, it is recommended to connect the trace wire ends together and the unmarked wire ends together. F. Using two (2) wire nuts (supplied), connect the wire ends at the ALL-CLEAR™ Photosystem receiver to the pigtail wire ends coming out of the receiver unit. Although not required, it is recommended to connect the trace wire ends together and the unmarked wire ends together. STEP 4 : Final Installation 104382 D: AUXILIARY EQUIPMENT WARNING RISK OF ENTRAPMENT. DISCONNECT POWER TO THE OPENER BEFORE AND DURING INSTALLATION OF THIS ACCESSORY. DO NOT RECONNECT POWER TO OPENER UNTIL INSTRUCTED TO DO SO. ENSURE DOORWAY IS CLEAR BEFORE STARTING TESTING OF UNIT. AN AUTOMATIC GARAGE DOOR SYSTEM POSES A THREAT OF INJURY OR EVEN DEATH. INSTALL THE ALL-CLEAR PHOTOSYSTEM NO HIGHER THAN 4” - 6” ABOVE THE GARAGE FLOOR TO REDUCE THE RISK TO SMALL CHILDREN. WARNING D: AUXILIARY EQUIPMENT A. Attach the"U" brackets to the "L" brackets with a 1/4-20 carriage bolt, washer and hex nut (provided). Insert the bolt from the inside of the "U" bracket and hand tighten only at this time. B. Place the transmitter and receiver units into their respective "U" brackets. See Illustration, at right. C. Connect the interconnect wire pair to the garage door opener terminals marked "4" & "5". Although not required, it is suggested that the "trace" be connected to Terminal 5. See Wiring Diagram, Page 21. STEP 5 : Final Alignment and Test A. Reconnect the power to the Garage Door Opener. Keep a portable transmitter with you to control the garage door opener. B. Place a solid object one foot in front of the transmitter or receiver. The red LED should go OFF and remain OFF until the object is removed. NOTE: There may be a slight delay in returning to normal depending upon how long the photosystem was blocked. C. Move to the center of the door. Make sure the red LED light is on. Move a solid object slowly through the beam. The LED should go OFF and then ON. If not, check the wire connections (see Step 3). D. At this time set or recheck the down limit adjustment and reversing system adjustment of the garage door opener following the procedure outlined in Steps 1 & 4, Pages 17 & 18. It is VERY IMPORTANT that the door opener's inherent features operate as intended before completing the photosystem tests. E. Place an opener insert box or a similar object (at least six inches high) on the floor at the center of the door. Now, attempt to close the door. The door should NOT close from the portable transmitter, but will close with constant pressure from the mechanical push button. F. Remove the obstruction from the photosystem beam’s path. Close the door. Toward the bottom of the doors downward movement, CAREFULLY move a solid object across the path of the beam at the center of the door. The door should STOP, pause for approximately one second and OPEN. Retest, breaking the beam one foot in front of both the transmitter and receiver unit while the door is moving downward. The door must STOP and OPEN each time. If not, re-align the photosystem until proper operation is obtained. G. Tighten all mounting screws and bolts. 104383 INSTALLATION OF RADIO CONTROLS: The following instructions detail installation of Model 9931 Radio Controls. For other Radio models, see instructions packaged with product. TRANSMITTER: To gain access to the Transmitter Coding Switches, remove the Battery Cover from the front of the Transmitter by sliding it toward the bottom of the Transmitter as illustrated. 104384 RECEIVER: The Receiver Coding Switches can be accessed by removing the small door from the back of the Receiver using a small screwdriver or knife. 104385 14 D: AUXILIARY EQUIPMENT Setting The Coding Switches: When setting the Coding Switches THE FACTORY PRE-SET CODES MUST BE CHANGED TO PREVENT UNAUTHORIZED OPERATION. Transmitter and Receiver codes must be set IDENTICALLY. If just one Code Switch is mismatched, the Radio Controls will not function. NOTE: For security reasons, it is advisable NOT to set all the switches in the same position. Mounting The Receiver: After setting the Coding Switches, mount the Receiver on the rear panel of the Opener by connecting it to Terminals 1, 2 and 3. A small Plastic Pin is provided to secure the other end of the Receiver to the panel. For proper operation, the Antenna Wire should be POINTED STRAIGHT DOWN toward the f...

Herunterladen

Geben Sie zwei Ziffern: