Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
2 WARNING HIGH VOLTAGE ONLY A QUALIFIED TECHNICIAN SHOULD SERVICE THIS GATE OPERATOR PERIODICALLY TEST SENSITIVITY OF OVERLOAD *** READ MANUAL *** DATES DATE TESTED DATE TESTED DATE TESTED DATE TESTED SERVICED LOG DATE OVERLOAD TEST Pre-Installation Notes................................................... 3 Operator Class Designation ................................... 3 Section A: Gate System Design/Installation ............. 4 Section B: Preparing the Site ..................................... 6 The Concrete Operator Pad.................................... 6 Placing the Vehicle Detector Loops ..................... 6 Electrical Power Requirements.............................. 8 Section C: Installing the Operator ............................. 9 Placing the Mechanical Unit ................................. 10 Installing the Arm ..................................................10 Installing the Control Box..................................... 11 Electrical Hookup ..................................................11 Schematic and Wiring Diagram............................ 11 Wiring the Mechanical Unit and Control Box...... 12 Bi-Parting Wiring Diagrams..................................13 Accessory Equipment Hookup .................. 13,15,16 READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes throughout this manual are there to protect you and your equipment. Pay close attention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. CAUTION Indicates a MECHANICAL hazard of DAMAGE to your gate, gate operator, or equipment. Gives instructions to avoid the hazard. Indicates an ELECTRICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard. WARNING Indicates an ELECTRICAL hazard of DAMAGE to your gate, gate operator, or equipment. Gives instructions to avoid the hazard. CAUTION TABLE OF CONTENTS Pre-Setting the Motor Overload Sensitivity......... 17 Terminal Strip Reference Chart.....................17 - 19 Section D: Starting the Operator.............................. 19 Setting the Limit Switches .................................... 19 Setting the Switch Selectable Options ................ 19 No Load Test Mode................................................ 19 Applying Power......................................................20 Indicator Lamps .....................................................20 Maximum Run Timer..............................................22 Final Settings .........................................................22 Section E: Auxiliary Equipment ............................... 23 Section F: End User Instructions ............................. 24 Safety Guide for the End User.............................. 24 Operational Guide for the End User..................... 25 Operator Exploded View & Parts List .............. 26 & 27 Technical Specifications............................................ 28 Figure 1: Test Log PRE-INSTALLATION NOTES The Allstar Gate Star 4000 (GS4000) Vehicular Gate Operator will provide convenience and assurance to the ultimate users for many years. It is ruggedly built of the finest materials and has been thoroughly inspected and tested at the Allstar factory. It has many features that will aid in the installation and testing of the complete gate system. The GS4000 is certified to comply with UL Standard for Safety 325, as revised March 1, 2000. (115 Volt version only.) NOTICE - BEFORE ATTEMPTING INSTALLATION, READ THIS MANUAL CAREFULLY SO YOU WILL BE THOROUGHLY FAMILIAR WITH THE FEATURES OF THE GS4000 AND ITS PROPER INSTALLATION PROCEDURES. The GS4000 Vehicular Swing Gate Operator is designated a Class I Residential Vehicular Swing Gate Operator, and is intended to operate a vehicular swing gate installed on a residential home, maximum of four single families in the dwelling, or a garage or parking area associated with that home. The GS4000 vehicular gate operator is also designated Class II (Commercial location or multi-family home); III (industrial location not intended to service the general public); and IV (secure or restricted access locations, ie. airports and prisons). The GS4000 may be used in any Class location. Because the Allstar GS4000 (as well as gate operators sold by other manufactures) is designed to start and move gates weighing as much as 1000 pounds,---the Allstar GS4000 is capable of producing high levels of force. It is important in the design of the total gate system that designers, installers and users be aware of the hazards that may be associated with the IMPROPER design, installation and use of Vehicular Gate systems and Gate Operators. The gate operator is only one part of a complete automatic gate operating system. As each location and usage is different, a properly designed system will include all applicable safety devices. The GS4000 CGA2K™ Technology provides several features that can help redu...